Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

INSTALLATION INSTRUCTIONS

Prepare Location

■It is recommended that the vent system be installed before hood is installed.

■If you are installing the optional backsplash with shelves for heat lamps, follow the instructions included with that product.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check that all installation parts have been removed from the shipping carton.

1.Disconnect power.

2.Determine which venting method to use: roof or wall exhaust.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

The hood is attached to the wall with the wood support that is attached to the back of the hood.

1.Determine and mark the centerline on the wall where the canopy range hood will be installed.

2.Select a mounting height between a minimum of 30"

(76.2 cm) and a suggested maximum of 36" (91.4 cm), above the cooking surface and the bottom of the range hood and mark a horizontal reference line on the wall.

3.Remove the wood support from the back of the range hood by loosening the 2 screws from the inside. Locate and level the top of the wood support 15³⁄₈" (39.1 cm) above the marked horizontal line and centered on the vertical centerline. Using 2 - 4 of the 6 x 80 mm screws, install wood support so that it is screwed into at least 2 vertical studs.

15³⁄₈"

 

(39 cm)

A

30" (76.2 cm) to 36" (91.4 cm)

B

A. Wood support

B. Centerline

NOTE: The screws provided for mounting this hood must be fastened into solid wood. Do not fasten into sheet rock only.

8

Page 7 Page 9
Page 8
Image 8
Jenn-Air W10274316B, LI3UNB installation instructions Installation Instructions, Electrical Requirements, Prepare Location
Page 7 Page 9

LI3UNB, W10274316B specifications

The Jenn-Air LI3UNB, W10274316B, represents a pinnacle of performance and elegance in the realm of kitchen appliances. This powerful kitchen solution combines advanced technology with sophisticated design, making it an ideal choice for culinary enthusiasts and home chefs alike.

One of the standout features of the Jenn-Air LI3UNB is its highly efficient cooling system. Designed with an advanced compressor and evaporator, this model ensures consistent temperature regulation, keeping food fresher for longer. The unit's customizable temperature settings allow users to efficiently store a variety of items, from vegetables to fine wines, catering to diverse storage needs.

In addition to its cooling efficiency, the LI3UNB boasts a sleek, modern aesthetic that integrates seamlessly into any kitchen décor. Its stainless steel finish is not only visually appealing but also resistant to smudges and fingerprints, ensuring that the appliance maintains its luxurious appearance over time. The minimalist design is complemented by hidden hinges, providing a clean, unobtrusive look.

The LI3UNB model is engineered for convenience, featuring adjustable shelving that offers flexibility in storage configurations. Users can easily accommodate taller items such as wine bottles or large platters, enhancing organizational capabilities. Furthermore, the built-in LED lighting illuminates its interior, making it easy to find what you need without rummaging through.

Technologically, the Jenn-Air LI3UNB is equipped with smart features that elevate its functionality. Some models come with Wi-Fi connectivity, enabling users to control and monitor their appliance remotely. This means that whether you’re away from home or lounging on the couch, you can adjust temperatures or receive alerts about any potential issues, adding an extra layer of peace of mind to your food storage.

Moreover, the LI3UNB embraces energy efficiency. It operates quietly while consuming significantly less energy compared to older models, making it environmentally friendly while also helping to reduce utility bills.

For those who appreciate culinary excellence, the Jenn-Air LI3UNB, with its combination of style, performance, and smart technology, is a remarkable choice. It redefines what users should expect from kitchen appliances, elevating everyday cooking and food preservation experiences to extraordinary heights.
Top Page Image Contents