UV10
OPERATING INSTRUCTIONS
Power On / Off
Press the
/SRC button (10) on the unit (or the
button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears
MENU, touch the top left corner of the screen or press the SRC button on the front panel (10) or remote control (8) .
Volume Adjustment
Volume Increase/Decrease
To increase or decrease the volume level, turn the rotary encoder (11) on the front panel or press the
in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen.
Press and hold the
button to power off the unit.The monitor is drawn back into the main compartment.
RADIO
SOURCE MENU
(15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The LCD or TFT screen displays the volume level for 3 seconds.
Programmable
Audible Beep Confirmation
An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu.
Mute/Line Mute
Press the rotary encoder button (11) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit. Press the rotary encoder button again to restore the volume. “MUTE” is displayed on the LCD. Adjusting the volume or using any of the audio setup features cancels the mute function.
If the “MUTE” wire is connected, audio output mutes when a telephone call is received by the car phone (using optional BTM10) or when verbal navigation is performed (using optional NAV102).
Playing Source Selection
When the monitor is closed, press the SRC button on the front panel (10) or remote control (8) to change between available audio playing sources in the following order: AM/ FM, DISC, USB1, USB2, BT, NAV, AUX IN and CAMERA. The mode is displayed on the LCD screen.
Source Menu
You can also use the touch screen to change the source through the SOURCE MENU. To access the SOURCE
RADIO DISC USB1 USB2
BT NAV AUX CAMERA
Touch the DISC, RADIO, USB1, USB2, NAVI, AUX or CAMERA button to select the corresponding source.
NOTE: If an iPod is attached to a USB1 port, “IPOD” appears instead of the text “USB1.”
External Devices
External peripheral devices, including a game console, camcorder, navigation unit, iPod, Zune, etc. can be connected to this unit via RCA output using an A/V Media Adapter Cable (not included).
EJECT
A / V |
|
|
INPUT | 1 | Right Audio |
| 2 | Left Audio |
| 3 | Ground |
| 4 | Video |
3.5mm A/V Cable (not included)
Connect the external device to the A/V Media Adapter Cable and then plug the cable into the A/V INPUT connector (13) on the front of the radio. Select “AUX” or “AUX IN” (when monitor is closed) mode to access auxiliary devices. You cannot directly control external devices connected to the A/V INPUT. For information regarding the use of USB devices, see “Inserting a USB Device” on page 17.
This feature allows the user to select a
To program a specific
Audio Control Menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.
Touch the EQ button on the left side of the screen or press the EQ button (32) on the remote control to display the audio menu.
•Use the touch screen +/- buttons to adjust the settings for an audio feature.
•To adjust an audio feature using the remote control, perform the following steps:
a.Press the (>>)/(<<) buttons (19, 17) to highlight the audio feature to be adjusted.
b.Press the >/ button (18) to select the highlighted option.
6
