VM9213

USING THE TFT MONITOR

Open/Close TFT Monitor

Open TFT Monitor

Press the OPEN button (4) on the front panel or press the ( ) button (25) on the remote control to activate the mechanism that moves the display panel into the viewing position.

Close TFT Monitor

Press the OPEN button (4) on the front panel or press the ( ) button (25) on the remote control to load the display panel back into the compartment.

TFT Monitor Auto Open

If “TFT Auto Open” is “On” when the unit is turned on, the monitor automatically moves to the viewing position.

If “TFT Auto Open” is ”Off” when the unit is turned on, press the OPEN button (4) or ( ) button (25) on the remote control to move the monitor into the viewing position.

If “TFT Auto Open” is set to ”Manual”, the TFT will not close when the key is turned off.

Monitor Tilt Angle Adjustment

A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods:

Step by Step Angle Adjustment

Press the () or () button on the remote control (27, 26) to adjust the tilt angle of the screen one step at a time. Press once to adjust the downward tilt angle of the screen one step at a time or press and hold to adjust the angle in a continuous motion.

You can also adjust the tilt by pressing the TILT button (1) and then using the rotary encoder (5) to adjust the angle while the read tilt icon is visible on the TFT screen.

Continuous Angle Adjustment

Press and hold the () or () button on the remote control to adjust the tilt angle in a continuous motion.

Aspect Ratio

Press the WIDE button (28) on the remote control or the WIDE/<< button (2) on the monitor to adjust the aspect ratio as follows:

FULL

The entire screen is extended horizontally to the aspect ratio of 16 to

9.The extension ratio is the same at any point.

NORMAL

The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display.

STANDBY

Screen becomes black. Touch screen to resume.

Image Setting

Table 2 shows the video output mode for each playing source.

Table 2: Video Output Modes

Playing Source

Video Output Modes

 

 

 

 

AM/FM TUNER

RGB Mode

 

 

DVD

RGB Mode

 

 

BT

RGB Mode

 

 

AUX IN1

CVBS Mode

 

 

AUX IN2

CVBS Mode

 

 

NAV

CVBS Mode

 

 

CAMERA

CVBS Mode

 

 

*CVBS – Composite Video Baseband Signal

Parameter Adjustment Procedure

1.Enter Picture Quality Setting Mode:

Press the PIC button (24) on the remote control or the PIC/BAND button (3) on the monitor.

2.Select Item to Set:

Press the AUDIO button (5) on the control panel to select “BRIGHT” or “CONTRAST”.

3.Set Parameters:

Press the +/– buttons (15, 16) on the remote or turn the rotary encoder (5) on the control panel.

4.Exit Picture Quality Setting Mode:

Press the PIC button (24) on the remote control or the PIC/BAND button (3) on the monitor

Parking Brake Inhibit

When the pink "Parking" wire is connected to the vehicle Parking Brake circuit, the front TFT monitor will display video when the Parking Brake is engaged. (When the pink wire is grounded via the Parking Brake circuit, video will be displayed.)

Monitor Movement Mechanism

If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor:

Table 3: Monitor Protective Measures

Obstruction

Self

OPEN Button

Power

Protection

Pressed

Reconnected

 

 

 

 

 

 

 

 

 

Monitor load-

Monitor is auto-

Monitor fully

Monitor is auto-

ing out hori-

matically

extended hori-

matically

zontally

loaded into unit

zontally

loaded into unit

Monitor load-

Unit stops at

Monitor fully

Monitor is auto-

ing in hori-

obstruction

extended hori-

matically

zontally

point

zontally

loaded into unit

Monitor load-

Unit stops at

Monitor swiv-

Monitor swiv-

ing out verti-

obstruction

els back to the

els back to the

cally

point

unit

unit

Monitor load-

Unit stops at

Monitor swiv-

Monitor swiv-

ing in verti-

obstruction

els back to the

els back to the

cally

point

unit

unit

After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (4) or disconnecting and reconnecting the power.

6

Page 10
Image 10
Jensen VM9213 operation manual Using the TFT Monitor