48
13-2 Other problems
Action
•Set the [REMOTE] switch to “LOCAL”.
•Set the No. 002 <OPERATION LOCK>
menu switch to “OFF”.
•Connect the monitor to the [MONITOR
OUT] connector.
•Set the No. 500 <ON SCREEN> menu
switch to “ON”.
•Read the instructions on page 7 and clean
the heads.
———
•Press the [MENU] button and restore the
normal mode.
•Read “Recording preparation” on page 26
and check the setting.
Causes
• The [REMOTE] switch is set to
“REMOTE”.
• The No. 002 <OPERATION LOCK> menu
switch is set to “ON”.
• The monitor is not connected to the
[MONITOR OUT] connector.
• The No. 500 <ON SCREEN> menu switch
is set to “OFF”.
• The heads are dirty.
• The counter does not run on a non-
recorded section of the tape.
• The menu switch setting mode is
engaged.
• Check the input switch settings on the
front panel or menu switch to ensure that
they are correct.
Symptoms
The VCR’s controls are not
functioning.
On-screen display does
not come up.
Noise appears on parts of
the playback picture.
Tape counter does not run.
The input video image is
not output.
14-1 Optional equipment
SA-K46 RS-232C interface board
With this board connected to this unit and a personal
computer, you can control the VCR from a personal
computer. Use a reverse-type cable. For installation and
uninstallation, consult your JVC dealer.
RM-G30 wired remote control
This remote control allows you to control all basic VCR
operations such as PLAY, RECORD, PAUSE, FF, etc.
YC video cables
These cables are used to transmit YC video signals.
The following types are available.
Types Input Output Length
VC-G30 4-pin 4-pin 3 m
VC-G50 4-pin 4-pin 5 m
VC-G3030 4-pin 7-pin 3 m
VC-G2030 7-pin 4-pin 3 m
VC-G2050 7-pin 4-pin 5 m
14 APPENDIX13 TROUBLESHOOTING
VC-G8030 remote extended cable
This extended cable is for use with the RM-G800 remote
controllers. The cable length is 3 m.
49
15 SPECIFICATIONS5Audio input
Line : –8 dBs, 10 kΩ, unbalanced
Mic : –67 dBs, 3 kΩ, unbalanced
5Audio output
Line : –8 dBs, 1 kΩ, unbalanced
Headphone : – infinity to –17 dBs, 8 Ω,
unbalanced
[Time code]
5Input : 0 dBs ± 3 dBs, high impedance,
unbalanced
5Output : 0 dBs ± 3 dBs, low impedance,
unbalanced
[DV interface]
5Input/output : IEEE 1394
[Connectors]
5RS-422 interface: D-sub 9-pin
5JVC bus
connector : DIN 12-pin
Accessories
AC cable x 1
Head cleaning tape x 1
Option
SA-K46U RS-232C interface board
Design and specifications subject to change without notice.
Dimensions (unit: mm)
General
5Power
requirements : AC 120 V (U MODEL), AC 220 V –
240 V (E MODEL), 50 Hz/60 Hz,
DC 12 V (11 V to 17 V)
5Power
consumption :
30 W (U MODEL), 280 mA (E MODEL)
5Dimensions : (W) 212 mm x (H) 88 mm x (D) 325 mm
(8-3/8" x 3-1/2" x 12-13/16")
5Weight : Approx. 3.6 kg (7.9 lbs.)
5Temperature
Operating : 5°C to 40°C (41°F to 104°F)
Storage : –20°C to 60°C (-4°F to 140°F)
5Humidity
Operating : 30% to 80% RH
5Format : MiniDV format
5Signal format : NTSC (U MODEL), PAL (E MODEL)
5Usable tape : MiniDV tape
5Tape width : 6.35 mm
5Tape speed : 18.812 mm/s (SP mode) (U MODEL)
18.831 mm/s (SP mode) (E MODEL)
5Record/play
time : 60 minutes (with an M-DV60ME
tape, only in the SP mode)
5FF/rewind time :
Within 120 s (with an M-DV60ME tape)
[Video]
5Video signal
recording
format : 8-bit, 13.5 MHz, 4:1:1 component
recording (U MODEL)
: 8-bit, 13.5 MHz, 4:2:0 component
recording (E MODEL)
5Sampling
frequency :
Y: 13.5 MHz, R-Y/B-Y: 3.375 MHz (U MODEL)
5Video inputs
Analog composite: 1.0 V (p-p), 75 Ω
Analog Y/C : Y: 1.0 V (p-p), 75 Ω
C: 0.286 V (p-p), 75 Ω (Burst) (U MODEL)
C: 0.3 V (p-p), 75 Ω (Burst) (E MODEL)
Analog component:Y: 1.0 V (p-p), 75 Ω
R-Y/B-Y: 0.7 V (p-p), 75 Ω
5External sync
input : 1.0 V (p-p), 75 Ω
5Video output
Analog composite: 1.0 V (p-p) (setup can be switched
ON/OFF with a menu switch [U
MODEL]), 75 Ω
Analog Y/C :Y: 1.0 V (p-p) (setup can be
switched ON/OFF with a menu
switch [U MODEL]), 75 Ω
C: 0.286 V (p-p), 75 Ω (Burst) (U MODEL)
C: 0.3 V (p-p), 75 Ω (Burst) (E MODEL)
Analog component :Y: 1.0 V (p-p) (setup can be
switched ON/OFF with a menu
switch [U MODEL]), 75 Ω
R-Y/B-Y: 0.7 V (p-p), 75 Ω
5Horizontal
resolution : 500 lines or more
[Audio]
5Audio signal
recording format: 16-bit, 48 kHz for two channels or
12-bit, 32 kHz PCM for four channels
5Frequency
response : 20 Hz to 20 kHz (48 kHz, 16 bits)
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD SHIFTA. DUB
ADVANCEPRESET
REWSTOP FF
RECPLAY
PAUSE
ON/OFF
VIDEO CASSETTE RECORDER BR-DV600UA
V.IN/A.MONIA.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4
Y/C
(CPN)
LINE
L
R
MIX
MIX
325
33
51
27
212
27
88