JVC DR-MH30S, DR-MH20S manual Relief Recording

48 EN TIMER RECORDING

	Manual Timer Programing			6 Press rt to select “START”, then press ENTER. Press rt to
				set the desired start time, then press ENTER.
				● Each press of rt advances/goes back the start time in 1-min.
You can program this unit to timer-record as many as 32 programs.
				increments.
If you do not know the VCR Plus+ number for the program you				● To advance/go back the start time in 30-min. increments, press and
wish to record, use the following procedure to set your unit to				hold rt.
timer-record the program.				7 Press rt to select “STOP”, then press ENTER. Press rt to
				set the desired stop time, then press ENTER.
● Make sure that the unit’s built-in clock is set properly.
				● Each press of rt advances/goes back the stop time in 1-min.
● Turn on the unit.				increments.
● Turn on the TV and select the AV mode.				● To advance/go back the stop time in 30-min. increments, press and
● Slide the TV/CABLE/DBS/DVD switch to DVD.				hold rt.
				8 Press rt to select “SOURCE”, then press ENTER. Press rt
		CABLE/DBS		to select the desired source, then press ENTER.
		TV	DVD	9 Press rt to select “CH”, then press ENTER. Press rt to
				select the desired channel.
				10 Press rt to select “CONFIRM”, then press ENTER.
				11 Set the other recording options as required.
				● Refer to step 8 in “VCR Plus+® Timer Programing” ( pg. 46).

AUX	PROGRAM
ENTER
	rtwe

12 Press rt to select “OK”, then press ENTER to access the Program Confirmation screen.

13 Press w e to select “EXIT”, then press ENTER to complete timer programing.

●To program another timer, press w e to select “CONTINUE”, then press ENTER.

2PROGRAM > CALENDAR PROG. (3/3)

		01/08/03 WED 10:30PM - 11:00PM		DBS 100
		GARDENING	[EDUCATION] FR360
			1:00	28:00
SELECT WITH [	]	INPUT TITLE	GARDENING
THEN PRESS [ENTER]		CATEGORY	EDUCATION
PRESS [PROGRAM]
		WEEKLY/DAILY	MON-FRI (FOR A WEEK)
TO EXIT
		REC MODE	FR360

PROGRAM	ENTER
EXIT	O K
	SELECT

1 Load a recordable disc if recording to DVD.

2 Press PROGRAM to access the program top screen.

3 Press rtw e to select “CALENDAR PR.”, then press ENTER.

●When “PROGRAM FULL DELETE UNWANTED TIMER PROGRAMS” appears on the TV screen, you need to cancel some of the reserved programs. ( pg. 49)

4 Press rtw e to select the desired date, then press ENTER.

5 Press rt to select “RECORD			2 PROGRAM > CALENDAR PROG. (2/3)
TO”, then press ENTER. Press
			01/08/03 WED	10:30PM - 11:00PM DBS 100
rt to select the desired					[MISC. ] XP
recording deck, then press	SELECT WITH [	]
			RECORD TO		HDD
ENTER.	THEN PRESS [ENTER]
			START		10:30PM
	PRESS [PROGRAM]
			STOP		11:00PM
	TO EXIT
			SOURCE		DBS
			CH		100

PROGRAM	ENTER
EXIT	O K
	SELECT

●If “PROGRAM OVERLAPPED” appears on the TV screen, see page 49.

NOTES:

●When two successive programs are recorded on a DVD-RW disc with Manual Timer Programing function, the beginning of the second one may be left off the recording.

●If the copy limited program is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programed.

Cable Box and DBS Receiver Users

To timer-record a satellite broadcast using Manual Timer Programing:

APerform “Cable Box and/or DBS Receiver Control Setting” ( pg. 24).

B Perform “Manual Timer Programing” ( pg. 48). C Leave the cable box or DBS receiver’s power on.

Relief Recording

When a program that is set for the DVD deck cannot be recorded properly, the program is recorded to the HDD deck instead in the same recording mode as set.

●If the remaining capacity of the hard disc is not sufficient, the program is recorded to the DVD deck until the remaining capacity of the DVD disc lasts.

●If “JUST” is selected for the recording mode, the current recording mode for the DVD deck is applied.