JVC DR-MH50S Basic Connections, 16 EN INSTALLING YOUR NEW UNIT, connectors ^, 8 Basic Connection, connector accepts:, 8 S-VideoConnection, Set AL-1OUTPUTB to:

16 EN INSTALLING YOUR NEW UNIT

Basic Connections				8 Basic Connection
				To connect to a TV with 21-pin SCART input connector ^
				A Disconnect the TV aerial cable from the TV.
				B Connect the TV aerial cable to the [ANTENNA IN] connector on
				the rear panel of the unit.
				C Connect the [ANTENNA OUT] connector on the rear panel of
				the unit and the TV’s aerial connector with the supplied RF
				cable.
				D Connect the [L-1 IN/OUT] connector on the rear panel of the
				unit and the TV’s 21-pin SCART connector with a supplied 21-
TV aerial cable				pin SCART cable.
				● The [L-1 IN/OUT] connector accepts and delivers either a
				composite signal (regular video signal), Y/C signal or RGB
				signal.
				● Set your TV to the VIDEO (or AV), Y/C, or RGB mode
To [ANTENNA IN]			Mains outlet	according to the type of your TV’s SCART connector.
				8 S-Video Connection
		Mains power cord		To connect to TV’s S-VIDEO input and AUDIO input
				connectors ^
				A Perform A – C in ABasic ConnectionB.
				B Connect the unit’s [S-VIDEO OUT] connector to the TV’s
				S-VIDEO input connector.
				C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
				input connectors.
				● You can obtain high quality S-VHS pictures.
	To [L-1 IN/OUT]		Back of unit	● If your TV is not stereo capable, use the unit’s [AUDIO OUT]
				connectors to connect to an audio amplifier for Hi-Fi stereo
		To [AUDIO	To [S-VIDEO
				sound reproduction.
		OUT]	OUT]
				8 Component Video Connection
To	To [COMPONENT
[ANTENNA				To connect to TV’s component video input connectors ^
	VIDEO OUT (Y/PB/
OUT]				A Perform A – C in ABasic ConnectionB.
	PR)]	Audio cable
				B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
		(not supplied)	S-Video
				connectors to the TV’s component video input connectors.
	21-pin SCART		cable
RF cable				C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
			(not supplied)
(supplied)	cable			input connectors.
	(supplied)
				● You can obtain high-quality component video pictures.
				● If your TV is not stereo-capable, use the unit’s [AUDIO OUT]
	Component			connectors to connect to an audio amplifier for Hi-Fi stereo
	video cable			sound reproduction.
	(not supplied)			● By using the component video connection, you can view the
				images in the progressive mode. For switching to the
				progressive mode, refer to AScan Mode SetB (A pg. 72).
		TV		NOTE:
				Select an appropriate option of AL-1 OUTPUTB as follows
				(A pg. 64):
	To 75 ohm terminal			When your TV’s SCART
It’s essential that your unit be properly connected.					Set AL-1 OUTPUTB to:
				connector accepts:
ATTENTION:				Composite signals	ASCART VIDEOB
● Your TV must have a 21-pin AV input connector (SCART) for				Y/C signal (separated
the basic connection to the unit.				luminance (brightness) and	ASCART S-VIDEOB
● Connect the AC plug only after all connections to the TV has				chrominance (colour) signals)
been completed.				RGB signal	ASCART RGBB
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO				Component video signal	ACOMPONENTB
OPERATION CAN BE PERFORMED.
1 Make sure the package contains all of the accessories listed in				When the setting selected is not in accordance with the TV
				connected and depending on the type of appliance connected to
ASPECIFICATIONSB (A pg. 84).
				the unit, the correct picture will not appear.
2 Place the unit on a stable, horizontal surface.
				4 Plug the end of the mains power cord into a mains outlet.
3 Connect the unit to a TV depending on the TV and cables you				● ALOADINGB blinks on the front display panel when the AC plug
use.				of the mains power cord is connected into a mains outlet and it
				takes approximately 50 seconds for the unit to be turned on.
				This is not a malfunction.