Other Problems | JVC HR-S7950EU manual

			EN 65

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
8.	“ “, “” and “$“ on the front	● The loaded cassette has had its record	Remove the cassette and cover the hole
	display panel won’t stop blinking.	safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		Automatic Satellite Programme	recorded in its entirety. Next time make
		Recording.	sure you have enough time on the tape to
			record the entire programme.

OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1. Whistling or howling is heard from the		● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 56).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 65

JVC HR-S7950EU specifications Other Problems

Contents

Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector cover Rear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To Use 10 EN Check the contentsSituate the recorder Connect the recorder to TV Video Connection To connect to a TV with S-VIDEO/AUDIO in connectors 12 EN Auto Set UpTurn on the recorder Select your country Select the language Perform Auto Set UpConfirm/Set video channel On the front display panel 14 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or e Just Clock Language for the on-screen display Access the Country Set screen Access the Main Menu screenLanguage 16 EN Situate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections 18 EN Setting satellite receivers brand and channel VCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic Playback High-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playback Variable Speed Search 22 ENIndex Search Skip Search Repeat Playback Next Function MemoryManual Tracking Soundtrack Selection 24 EN Tape Remaining Time Instant Timer Recording ITR 26 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual Programmes Recording Playback Access the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 28 EN Access the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title 30 EN Express Timer Programming VPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+ Before performing the 24 Hour Express Timer Programming Enter the programme mode32 EN Set the programme start/stop time and channel Cancel or change a programme Disengage the timer modeReturn to the timer mode Access the Programme Check screen/display Confirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screen Recording mode Select the L-2 Select modeProgramme Recording Before performing the following steps 36 EN Navigation Programme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programme Select the programme 38 ENEdit Programme Title Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News 40 EN Edit From a Camcorder Another Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source player Output/Input Set Decoder connector Select and L-2 Input Setting Simple Connections Connecting To a Satellite Receiver Perfect Connections 46 EN Select the input modeConnect the decoder Set the tuner Make connections Connecting/Using a Stereo System Access the Mode Set screen Mode SetSelect the mode Select the mode setting Recorder is powered back on Using this video recorder as the source player for editingWith old tapes and rental cassettes Clear picture reproduction is also linked to this function Entire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder50 EN Function pg , set PROG. Navigation to OFF Indicator lights up on the front display panel Correction to the luminance signal to enhance detailS-VHS recording mode is selected Mode setting Colour System 52 EN Guide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program number Tuner Set Access the Auto Channel Set screen54 EN Auto Channel Set Press OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 56 EN Delete a Channel When Receiving a Scrambled Broadcast Set Stations B 58 ENSet Stations a Station Name TV Station And ID List 60 EN Access the Clock Set screenClock Set Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation Exit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 62 EN Power Recording 64 EN Other Problems Playback 66 EN Memory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS 68 EN Memo 70 EN