Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center.
| PROBLEM | POSSIBLE CAUSE | SOLUTION | |
|
|
|
| |
| The display does not light up. | The power cord is not plugged in. | Plug the power cord into an AC outlet. | |
|
|
|
| |
| No sound from speakers. | Speaker signal cables are not | Check speaker wiring and reconnect if necessary. | |
|
| connected. | (See page 6.) |
|
|
|
|
| |
|
| The SPEAKERS ON/OFF button is | Press SPEAKERS ON/OFF so that the sounds | |
|
| not set correctly. | come out of the speakers. (See page 13.) | |
|
|
|
|
|
|
| An incorrect source is selected. | Select the correct source. |
|
|
|
|
| |
|
| Muting is activated. | Press MUTING to cancel the mute. (See page 15.) | |
|
|
|
| |
|
| An incorrect input mode (analog or | Select the correct input mode (analog or digital). | |
|
| digital) is selected. | (See pages 13 and 14.) |
|
|
|
|
| |
| “NO SUBWOOFER” appears on the | The SUBWOOFER ON/OFF button is | If subwoofer is connected, set “SUBWOOFER | |
| display. | pressed while “SUBWOOFER” is set | YES” so that the SUBWOOFER ON/OFF button | |
|
| to “SUBWOOFER NO.” | works. |
|
|
|
|
| |
| Continuous hiss or buzzing during FM | Incoming signal is too weak. | Connect an outdoor FM antenna or contact your | |
| reception. |
| dealer. (See page 5.) |
|
|
|
|
|
|
|
| The station is too far away. | Select a new station. |
|
|
|
|
| |
| Noise is heard during FM/AM | An incorrect antenna is used. | Check with your dealer to be sure you have the | |
| reception. |
| correct antenna. |
|
|
|
|
| |
|
| Antennas are not connected properly. | Check connections. (See pages 5 and 6.) | |
|
|
|
| |
|
| Ignition noise from automobiles. | Move the antenna farther from automobile traffic. | |
|
|
|
|
|
| “OVERLOAD” starts flashing on the | Speakers are overloaded because of | 1. Press STANDBY/ON | on the front panel to |
| display. | high volume. | turn off the receiver. |
|
|
|
| 2. Stop the playback source. | |
|
|
| 3. Turn on the receiver again, and adjust the | |
|
|
| volume. |
|
|
|
|
|
|
|
| Speakers are overloaded because of | Press STANDBY/ON | on the front panel to turn |
|
| short circuit of speaker terminals. | off the receiver, then check the speaker wiring. | |
|
|
| If “OVERLOAD” does not disappear, unplug the | |
|
|
| AC power cord, then plug it back again. | |
|
|
| If speaker wiring is not | |
|
|
| dealer. |
|
|
|
|
|
|
| “DSP NG” appears on the display. | The | Press STANDBY/ON | on the front panel to turn |
|
| functioning correctly. | off the receiver. After unplugging the AC power | |
|
|
| cord, contact your dealer. |
|
|
|
|
|
|
| The STANDBY lamp lights up after | The receiver is overloaded because of | Press STANDBY/ON | on the front panel to turn |
| turning on the power, and soon the | a high voltage. | off the receiver. After unplugging the AC power | |
| receiver turns off again (into standby |
| cord, contact your dealer. |
|
| mode). |
|
|
|
|
|
|
|
|
| Remote control does not work. | There is an obstruction between the | Remove the obstruction. |
|
|
| remote sensor on the receiver and the |
|
|
|
| remote control. |
|
|
|
|
|
| |
|
| Batteries are weak. | Replace batteries. (See page 5.) | |
|
|
|
| |
| Remote control does not work as you | An incorrect remote control operation | Select the correct remote control operation mode. | |
| intend. | mode is selected. | (See pages 33 to 36.) |
|
|
|
|
|
|
| Only for |
|
|
|
| No sound effect such as Surround and | “DVD MULTI” is selected. | This is normal for “DVD MULTI.” | |
| DSP modes. |
|
|
|
|
|
|
|
|
English
37
