|
| TROUBLESHOOTING | EN 41 |
|
|
| |
Advanced features |
| Other problems | |
|
|
|
|
●Focus is set to the Manual mode.
➜Set Focus to the Auto mode. ( pg. 31)
●The lens is dirty or covered with condensation.
➜Clean the lens and check the focus again. ( pg. 48) ● The recording was done in a dark place, or the contrast
was low.
Snapshot mode cannot be used.●The Squeeze mode (SQUEEZE) is selected.
➜Disengage the Squeeze (SQUEEZE) mode. ( pg. 25, 26)
The color of Snapshot looks strange.●The light source or the subject does not include white. Or there are various different light sources behind the subject.
➜Find a white subject and compose your shot so that it also appears in the frame. ( pg. 18, 31)
●The Sepia (SEPIA) or Monotone (MONOTONE) mode is activated.
➜Disengage the Sepia (SEPIA) and Monotone (MONOTONE). ( pg. 25, 31)
The image taken using Snapshot is too dark.●Shooting was performed under backlit conditions. ➜Press BACKLIGHT. ( pg. 33)
●The temperature of the battery is extremely high/low.
●Charging is difficult in places subject to extremely high/low temperatures.
➜To protect the battery, it is recommended to charge it in places with a temperature of 10°C to 35°C (50°F to 95°F). ( pg. 45)
“SET DATE/TIME!” appears.●The date/time is not set. ➜Set the date/time. ( pg. 8)
●The
date/time has been erased.
➜Consult your nearest JVC dealer for replacement.
There is no picture.●The camcorder is not getting power, or some other malfunction exists.
➜Turn the camcorder’s power off and on again. ( pg. 8)
Some functions are not available using the MMENU/VOL. Wheel.●The Power Switch is set to “A”.
●The subject is too bright.
➜Set “r” to “SPOTLIGHT”. ( pg. 31)
White Balance cannot be activated.●The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
➜Disengage the Sepia (SEPIA) or Monotone (MONOTONE) mode before setting White Balance. ( pg. 31)
Wipe/Fader effects do not work.●The Power Switch is set to “A”.
➜Set the Power Switch to “M”. ( pg. 8)
The Black & White Fader does not work.●The Sepia (SEPIA) or Monotone (MONOTONE) mode is activated.
➜Disengage the Sepia (SEPIA) and Monotone (MONOTONE). ( pg. 25, 31)
Program AE with special effects does not work.●The Power Switch is set to “A”.
➜Set the Power Switch to “M”. ( pg. 8)
The image looks like the shutter speed is too slow.●When shooting in the dark, the unit becomes highly
sensitive to light when “GAIN UP” is set to “AUTO”.
➜If you want the lighting to look more natural, set “GAIN UP” to “AGC” or “OFF”. ( pg. 25, 26)
—
●Files stored in the memory card are protected.
➜Remove protection from the files stored in the memory card and delete them. ( pg. 22)
When the image is printed from the printer, a black bar appears at the bottom of the screen.
●This is not a malfunction.
➜By recording with “DIS” activated ( pg. 25, 26) this can be avoided.
When the camcorder is connected via the DV connector, the camcorder does not operate.
●The DV cable was plugged/unplugged with power turned on.
➜Turn the camcorder’s power off and on again, then operate it.
The rear of the LCD monitor is hot.●The light used to illuminate the LCD monitor causes it to
become hot.
➜Close the LCD monitor to turn it off or set the Power Switch to “OFF”, and let the unit cool down.