JVC Model DLA-HX1E manual Adjustments and Settings Using Menus, p “Capture start”, “Page 1”

Adjustments and Settings Using Menus

p“Capture start”

The status of capture is displayed in bold.

“Capt. in prog. (approx. 2min)” The image is being read into the projec- tor. During this time interval, the projec- tor will not respond to any command sig- nal inputted by the user.

“Signal can not be captured” Clear the message with the [EXIT] but- ton and input appropriate signals.

“Reduce capt. size”Clear the message with the [EXIT] but- ton and decrease the signal size.

•Depending on the image content, there will be cases where certain sig- nals cannot be captured while others of the same size can be.

q“Options” menu (“Page 1”)

The items of the “Options” menu shown below can be adjusted.

• The “Options” menu consists of two pages (“Page 1” and “Page 2”).

“Page 1”

Adjustment item (press / )	Adjustment content (press  / )
“Color profile”	Sets the color table.
	[ Press the [ENTER] button to enter the
	“Color profile” menu w.
“Menu display”	Sets whether the menu display automati-
	cally clears after 15 seconds.
	Values : “15sec”, “ON”	{“15sec”}
“Line display”	Sets whether the line display is shown for
	about 5 seconds.
	Values : “5sec”, “OFF”	{“5sec”}
“Flip H”	Reverses image left to right.
	Values : “ON”, “OFF”	{“OFF”}
“Flip V”	Inverses image upside down.
	Values : “ON”, “OFF”	{“OFF”}
“Page 2”	Displays “Page 2” of the “Options” menu.
	[ Press the [ENTER] button to enter the
	“Options” menu (“Page 2”) e.

w“Color profile” menu

To choose the color table of the image signals, press the (
/ ) CUR- SOR buttons. When using “Color profile”, set the “Color temp.” to “6500”.

•No display in the absence of image signal input. Values : “------”, “HDTV”, “MacRGB”, “NTSC”, “PAL”

{“------”}

e“Options” menu (“Page 2”)

Adjustment item (press / )	Adjustment content (press  / )
“Sleep time[min]”	Sets the length of sleep time which, when
	lapsed, automatically puts the projector
	into stand-by state if no signal is input-
	ted.
	Setting value: “15”, “30”, “60”, “OFF”
		{“OFF”}
“Menu color”	When “ON”, menu becomes transparent
	and the background can be seen through
	it.
	Setting value: “OFF”, “ON”	{“OFF”}
“PC2(BNC)”	Sets whether to use the BNC connector
	on the back of the projector as an “RGB”
	signal input terminal or as a “YPBPR”
	(color-difference) signal input terminal.
	Please reset it based on the connected
	apparatus.
	• The input will be “RGB” irrespective
	of the PC signal setting.
	Setting value: “RGB”, “YPbPr”	{“YPbPr”}
“DIST”	Image of high resolution can be achieved.
	Set as required.
	This is turned “ON” when the [OPERATE]
	button is pressed.
	Setting value: “OFF”, “ON”	{“ON”}
“SCART”	Connects to a Europe-adapted SCART
	plug and turns it “ON” during component
	input.
	Connect the Image Signal cable to the
	[RGB] terminal of the [PC2] input termi-
	nal and the Sync Signal cable to the
	[VIDEO IN] terminal.
	Setting value: “OFF”, “ON”	{“OFF”}
“RS-232C [bps]”	Sets the communication speed (signal
	transmission speed) when communicat-
	ing with a computer by using the [RS-
	232C] terminal. Please set the baud rate
	for transmission.
	Setting value: “9600”, “19200”	{19200}
“SXGA”	Select “1400” to project SXGA+ signal.
	Setting value: “1280”, “1400”	{1280}
“PC 3”	Set whether to use PC input or HDCP
	compatible video signal when using [PC3]
	terminal as input. Set according to the
	connecting equipment.
	Setting value : “PC”, “HDCP”	{“HDCP”}

r“Language” menu

Select the language in this language menu with the CURSOR buttons (
/ ).

Setting value : [] (Japanese), [English], [Deutsch] (German), [Español] (Spanish), [Italiano] (Italian), [Français]

(French), [Português] (Portuguese) and [] (Korean).

{[English]}

•Some words in the menu and proper nouns such as “VIDEO”, “NTSC”, “QUICK ALIGN...” are shown only in English.

39