Controls and Features
Connector Panel
1 [PC2] Input Terminal | 2 [PC1] Input Terminal | 3 [PC3] Input Terminal |
R PR/CR | G Y | B PB/CB H/CS | V |
PC2
DVI
PC3
PC1
SCREEN | REMOTE | Y/C | VIDEO | ||
TRIGGER AUDIO IN |
| CONTROL |
| VIDEO IN | |
4 [SCREEN |
|
|
|
|
|
|
|
6 [REMOTE] |
| 8 [Y/C] Input | |||||
TRIGGER] |
| Terminal |
| Terminal | |||
Terminal |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
5 [AUDIO IN] |
|
| 7 [CONTROL RS232C | 9 [VIDEO] Input | |||
| Terminal |
|
| IN/OUT] Terminal | Terminal | ||
1 [PC2] Input terminal (BNC x 5) |
|
| 4 [SCREEN TRIGGER] Terminal |
| |||
This is an input terminal for component signals (Y, CB, CR) or
(☞ page 21, 22)
To use this terminal, the “PC2(BNC)” item in the “Options” menu must be set correctly according to the input signals. (☞ page 39)
•Input of external sync signals is automatically detected. Detection of H/V signals or Cs signals causes automatic switching to external sync. The priority order is H/V>Cs.
•When computer signals are input, the uppermost edge of the image may appear to bow if the sync signal input is a composite sync (Cs) or G on sync signal. In this case, please use separate sync signals for vertical sync (V) and horizontal sync (H).
2[PC1] Input terminal (D-sub 3 rows 15 pin)
This is an input terminal dedicated to computer signals (RGB Video signals and sync signals).
Connect the display output terminal of the computer to this terminal. When a Macintosh computer is to be connected, please use the conversion adapter (sold separately) for Mac. (☞ page 22)
•When computer signals are input, the uppermost edge of the image may appear to bow if the sync signal input is a composite sync (Cs) or G on sync signal. In this case, please use separate sync signals for vertical sync(V) and horizontal sync(H).
3[PC3] Input terminal (DVI-D 24 Pin Dual/ Single)
HDCP compatible video signals (480p, 720p 60/59 Hz, 1080i 60/59 Hz) and input terminal for personal computer (PC) signal. Connect the display output terminal of the computer to this terminal. (☞ page 22)
•The menu screen for HDCP compatible signal input is the same as when PC input is selected.
The signal output for controlling
(Tip = DC +12 V, Sleeve = Gnd)
Before using the supplied cable, read ‘How to use the [SCREEN TRIGGER] terminal cable’ on page 5.
5[AUDIO IN] (audio) Terminal (mini jack)
This is the audio input terminal for devices connected to [PC1], [PC2], [PC3], [VIDEO] or [Y/C]. Connect the audio output terminal of the device to this terminal.
(☞ page 21, 22)
•When [PC1], [PC2], [PC3], [VIDEO] or [Y/C] input is be- ing selected, the inputted audio signals will be reproduced by the projector speaker.
(Audio output for this projector is monaural.)
6[REMOTE] Terminal (stereo mini jack)
When the remote control is unable to work due to rear pro- jection etc., the [REMOTE] terminal can be used to connect an external sensor to the projector. The external sensor is not generally sold. Please check with your authorized dealer.
7[CONTROL RS232C IN/OUT] Terminal (D-sub 9 Pin)
This is the
(☞ page 23)
• For details, please check with your dealer.
8[Y/C] Input Terminal (Mini DIN 4 Pin)
This is the input terminal for Y/C
9[VIDEO] Input Terminal (RCA pin jack)
This is an input terminal for composite video signals. Con- nect this terminal to the composite video output terminal of a VCR, etc. (☞ page 21)
9
