JVC Model DLA-HX1E Control Panel on the Projector, Controls and Features, STAND BY Indicator

Controls and Features

Control Panel on the Projector

1[STAND BY] Indicator

Light on : In stand by mode.

Blinking : In cool down mode.

2[OPERATE] Indicator

Light on : During projection.

9[LAMP] Indicator

Light on : Indicates the lamp has been used for more than 1900 hours.

Blinking : Indicates the lamp has been used for more than 2000 hours.

Please change the lamp. (☞ page 10, 47, 55)

3[OPERATE] button

When this projector is in standby mode, pressing this but- ton for more than 1 second will turn the projector on and cause the [OPERATE] indicator to light up. Press it one sec- ond or more again, and the projector goes into the cool down mode and finally into stand by mode. (☞ page 25)

•The [OPERATE] button will not work within approximately 1 minute of the light-source lamp being turned on. Hence wait about 1 minute before pressing.

4[VOL.] ª / · buttons

Use these buttons to adjust the sound volume. (☞ page 27)

5[EXIT] button

Press this button to display the previous menu (For exam- ple, from sub menu to main menu). Pressing this button when the main menu is displayed will erase the menu.

(☞ page 35)

6[ENTER] button

Press this button to show the next menu (For example, from main menu to sub-menu). It is also used when [ENTER] is displayed against an item on the menu screen, or to choose the “Reset” option etc. (☞ page 35)

p[VIDEO] button

Use this button to select a device such as a video con- nected to the [VIDEO IN] terminal ([VIDEO] or [Y/C] Input terminal) of the projector. (☞ page 25)

q[PC] button

Use this button to select a device connected to the [PC1], [PC2] or [PC3] terminals. (☞ page 26)

w[H-KEYSTONE] button

Use this button to remove the horizontal trapezoidal distor- tion of the image projected on the screen. (☞ page 30)

e[V-KEYSTONE] button

Use this button to remove the vertical trapezoidal distortion of the image projected on the screen. (☞ page 30)

r[MENU] button

Use this button to enter or exit the menu mode. When the main menu is displayed, pressing this button will cause the menu to disappear. (☞ page 35)

tCursor (  /  /  /  ) buttons

These buttons are used in the menu mode to select an item, adjust the value etc. (☞ page 35)

7[HIDE] button

Use this button to temporarily halt the audio and video out- put. Press again to resume. (☞ page 29)

8[TEMP] Indicator

Blinking : Indicates the temperature inside the projector is abnormally high.

y[PRESET] button

This [PRESET] button only works as a reset button for the [VOL.], [V-KEYSTONE] and [H-KEYSTONE] adjustments done on the control panel and the [VOLUME], [V-KEY- STONE], [H-KEYSTONE] and [DIGITAL ZOOM] adjust- ments done on the remote control. (☞ page 28, 30)

When adjusting the volume, keystone or digital zoom (when the setting is displayed on the screen) the adjusted value is reset to that which was set when the projector was shipped from the factory. This button does not work for the menu (submenu) items.

About Cool Down mode	Note
After projection, the heated lamp will go through a 90 sec-	Please do not pull out the plug from the power outlet during
onds cool-down period known as the cool down mode. This	cool down mode. Please also do not block the exhaust vent
function is to prevent heat from the heated lamp causing	by standing the projector on its end or laying it on its side.
damage and deformation to the internal components of the
projector. It also prevents lamp breakage and shortened lamp
life.
The Cool down mode is indicated by the blinking [STAND
BY] indicator. During the cool down mode, pressing the
[OPERATE] button will not turn on the projector.
After the cool down process is completed, the projector will
automatically change to stand by mode.

11