JVC RX-6500VBK manual Setting the Speakers for the DSP Modes, Press Setting repeatedly until

English

Setting the Speakers for the DSP Modes

To obtain the best possible surround sound of the DSP (Digital Signal Processor) modes (see page 18), you have to register the information about the speakers arrangement after all connections are completed.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Center Delay Time Setting

Register the delay time of the sound from the center speaker, comparing that of the sound from the front speakers.

If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec. As the distance to the center speaker becomes shorter, increase the delay time.

•1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

•When shipped from the factory, delay time is set to 0 msec.

Front, Center, and Rear Speaker Setting

Register the sizes of all the connected speakers.

On the front panel ONLY:

1. Press SETTING repeatedly until “CENTER DELAY” appears on the display.

SETTING

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“FRONT SPK” (Front Speaker),

•Once you have pressed SETTING, MULTI CURSOR %/ Þ can be also used for selecting “CENTER DELAY.”

•The display changes to show the current setting.

“CENTER SPK” (Center

Speaker), or “REAR SPK” (Rear

Speaker) appears on the display.

2. Press MULTI CURSOR @/ #to select the delay time of the center speaker output.

MULTI CURSOR

•Once you have pressed SETTING, MULTI CURSOR %/ Þ can be also used for selecting the speakers.

MULTI CURSOR

2.Press MULTI CURSOR @/ #to select the appropriate item about the speaker selected in the above step.

LARGE SMALL NONE

LARGE: Select this when the speaker size is relatively large.

SMALL: Select this when the speaker size is relatively small.

NONE: Select this when you have not connected a speaker. (Not selectable for the front speakers)

3.Repeat steps 1 and 2 to select the appropriate items for the other speakers.

Notes:

• Keep the following comment in mind as reference when adjusting.

– If the size of the cone speaker unit built in your speaker is greater

than 12 cm, select “LARGE,” and if it is smaller than 12 cm,

select “SMALL.”

• If you have selected “NO” for the subwoofer setting, you can only

select “LARGE” for the front speaker setting.

• Pressing # increases the delay time from 0 msec (“C. DELAY: 0ms”) to 5 msec (“C. DELAY: 5ms”).

•Pressing @ decreases the delay time from 5 msec (“C. DELAY: 5ms”) to 0 msec (“C. DELAY: 0ms”).

Rear Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing that of the sound from the front speakers.

If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 msec. As the distance to the rear speakers becomes shorter, increase the delay time.

•1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

•Rear delay time for Dolby Digital and DTS Digital Surround is to be set to 5 msec.

•When shipped from the factory, delay time is set to 5 msec.

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“REAR DELAY” appears on the
display.

•Once you have pressed SETTING, MULTI CURSOR %/ Þ can be also used for selecting “REAR DELAY.”

•The display changes to show the current setting.

•	If you have selected “SMALL” for the front speaker setting, you
	cannnot select “LARGE” for the center and rear speaker settings.
•	When you change your speakers, you need to register the
	information about the speaker again.

2. Press MULTI CURSOR @/ #to select the delay time of the rear speaker output.

MULTI CURSOR

• Pressing # increases the delay time from 0 msec (“R. DELAY: 0ms”) to 15 msec (“R. DELAY: 15ms”).

•Pressing @ decreases the delay time from 15 msec (“R. DELAY: 15ms”) to 0 msec (“R. DELAY: 0ms”).

12