JVC RX-6500VBK Connecting the Power Cord, Putting Batteries in the Remote Control, Battery cover

Digital connections

This receiver is equipped with one DIGITAL OUT terminal and three DIGITAL IN terminals — one digital coaxial terminal and two digital optical terminal.

You can connect any digital equipment such as DBS tuner, DVD player, CD player, and MD recorder to one of the digital terminals using a digital coaxial cable (not supplied) or digital optical cable (not supplied).

IMPORTANT:

•When connecting the DVD player or the DBS tuner using the digital terminal, you also need to connect it to the video jack on the rear. Without connecting it to the video jack, you can view no playback picture.

•After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary.

–Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 14.

–Select the digital input mode correctly. For details, see “Selecting the Analog or Digital Input Mode” on page 14.

	DVD player, etc
When the component has a digital	DVD
coaxial output terminal, connect it to
the DIGITAL 1 (DVD) terminal, using a
digital coaxial cable (not supplied).
	DIGITAL 1
When the component has a digital	(DVD)
optical output terminal, connect it to
the DIGITAL 2 (CD) or DIGITAL 3	DIGITAL 2 (CD)
(DBS), using a digital optical cable
(not supplied).	DIGITAL 3 (DBS)

Before connecting a digital	PCM / DOLBY DIGITAL
	/ DTS
optical cable, unplug the	DIGITAL IN
protective plug.

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

Plug the power cord into an AC outlet.

Keep the power cord away from the connecting cables and the antenna. The

power cord may cause noise or screen

interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Note:

The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:

–When you unplug the power cord.

–When a power failure occurs.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

Putting Batteries in the Remote Control

Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1 2 3

1.	On the back of the remote control, remove the
	battery cover.
2.	Insert batteries. Make sure to match the polarity:
	(+) to (+) and (–) to (–).

English

When the digital recording equipment such as an MD recorder has a digital optical input terminal, connecting it to the DIGITAL OUT terminal enables you digital-to- digital recording.

MD recorder, etc

DIGITAL OUT

PCM / DOLBY DIGITAL

/ DTS

3. Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Notes:

•When shipped from the factory, the DIGITAL IN terminals has been set for use with the following components.

–DIGITAL 1 (coaxial): For DVD player

–DIGITAL 2 (optical): For CD player

–DIGITAL 3 (optical): For DBS tuner

•When you want to operate the CD player or MD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see page 5).

•When you want to operate the DVD player using the AV COMPU LINK remote control system, connect the DVD player also as described in “Analog connections” (see page 5).

•Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

7