JVC RX-7030VBK Press Analog Direct so that a Direct appears on the display, Press TV SOUND/DBS

Turning Analog Direct On and Off	Changing the Source Name	Remote
		NOT

You can enjoy the sound closer to the original source by overriding the sound adjustments such as speaker output level adjustments (see page 32), Digital Equalization (see page 32), Surround and DSP modes (see pages 34 to 39), Bass Boost (see page 22) and Midnight Mode (see page 20). You can only adjust the volume level while Analog Direct is in use.

•Once you have made adjustment, it is memorized for each analog source.

When you have connected an MD recorder to the TAPE/MD jacks or a DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display.

Press ANALOG DIRECT so that “A DIRECT” appears on the display.

The lamp on the button also lights up.

•Each time you press the button, Analog Direct turns on and off.

Notes:

•When digital input mode is in use, Analog Direct is not available.

•Turning on Surround or DSP mode cancels Analog Direct and previously selected sound adjustments are recalled.

•If Analog Direct is in use, Midnight Mode is temporarily canceled.

•Turning on Analog Direct cancels Input Attenuator (page 20) (and CC Converter for RX-8030VBK: below).

When changing the source name from “TV” to “DBS”:

1.Press TV SOUND/DBS.

• Make sure “TV” appears on the display.

2.Press and hold TV SOUND/DBS until “ASSGN DBS” appears on the display.

ANALOG

L R LINEAR PCM

SPEAKERS 1

VOLUME

Note:

When connecting a DBS tuner to the TV SOUND/DBS IN jacks, change the source name to “DBS,” which will be shown on the display when selected as the source. Otherwise you cannot view any picture from DBS tuner.

Making Sounds Natural	RX-8030V
	ONLY

JVC’s CC (Compensative Compression) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit–quantization and by expanding the sampling frequency to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz signals).

By using CC Converter, you can obtain a natural sound field from both digital and analog sources.

Press CC CONVERTER so that the lamp on the button lights up.

•Each time you press the button, CC Converter turns on and off (the lamp goes off) alternately.

Note:

You cannot use this function while Analog Direct is in use. If you turn on Analog Direct while this function is in use, this function will be canceled.

For RX-8030VBK:

When changing the source name from “TAPE” to “MD”:

1.Press TAPE/MD.

• Make sure “TAPE” appears on the display.

2.Press and hold TAPE/MD until “ASSGN MD” appears on the display.

For RX-7030VBK/RX-7032VSL:

When changing the source name from “TAPE” to “CDR”:

1.Press TAPE/CDR.

• Make sure “TAPE” appears on the display.

2.Press and hold TAPE/CDR until “ASSGN CDR” appears on the display.

To change the source name to “TV” and “TAPE,” repeat the

same procedure above.

Note:

Without changing the source name, you can still use the connectedcomponents. However, there may be some inconvenience.

•For RX-8030VBK:

–“TAPE” or “TV” will appear on the display when you select the MD recorder or DBS tuner.

–You cannot use the digital input (see pages 19 and 20) for the MD recorder.

–You cannot use the COMPU LINK remote control system (see pages 41) to operate the MD recorder.

•For RX-7030VBK/RX-7032VSL:

–“TAPE” or “TV” will appear on the display when you select the CD recorder or DBS tuner.

–You cannot use the digital input (see pages 19 and 20) for the CD recorder.

21