Activating the Surround Modes

 

 

Activating the Surround Modes

 

 

 

 

 

 

Available Surround modes vary depending on the speaker settings and the incoming signals. (See page 36.)

Activating one of the Surround modes for a source automatically recalls the memorized settings and adjustments (see pages 25 to 33.)

English

You can also use the buttons on the remote control for the same functions.

Activating the EX/ES setting

For multi-channel digital software, you can activate the EX/ES (7.1- channel) reproduction mode.

Once you have set EX/ES (7.1-channel) reproduction mode, it is stored in memory and will be called up whenever you activate the Surround mode which the memorized EX/ES (7.1-channel) reproduction mode can be applied to.

1.Select and play any source other than “DVD MULTI.”

Make sure you have selected the analog or digital input mode.

Surround modes are not valid for DVD MULTI playback mode.

2.Press SURROUND to activate the Surround mode.

For multi-channel digital software (except 2-channel and Dual Mono software), incoming signals are automatically detected and the appropriate surround mode is activated (see page 36 for details).

 

DIGITAL AUTO

 

L C

R

LINEAR PCM

 

SUBWFR

LFE

DIGITAL

SPEAKERS 1

LS

RS

 

 

VOLUME

Press EX/ES to select an appropriate setting for your enjoyment.

The currently selected EX/ES (7.1-channel) reproduction mode appears on the display.

Each time you press the button, it changes as follows:

EX/ES AUTO*:

According to the incoming signal, an

 

appropriate Surround mode is applied.

 

• For Dolby Digital EX and DTS-ES,

 

EX/ES (7.1-channel) reproduction is

 

applied.

 

• For 5.1-channel (or less) encoded

 

software, 5.1-channel reproduction is

 

applied.

 

 

EX/ES ON*:

Select to apply EX/ES (7.1-channel)

 

reproduction to both 5.1-channel and 6.1-

 

channel encoded software.

 

 

EX/ES OFF:

Select to cancel the EX/ES (7.1-channel)

 

reproduction.

 

 

*If the surround back speakers are not connected or deactivated, Virtual 6.1-channel surround is applied.

Notes:

When Surround mode is deactivated, pressing EX/ES will activate an appropriate Surround mode for the current source.

When an analog or digital 2-channel source is playing, you can adjust the EX/ES (7.1-channel) reproduction mode and store the setting, but it will not affect the current source.

When the source is one to which the EX/ES (7.1-channel) reproduction cannot be applied, you can adjust the setting and store in memory, but reproduction channels will remain unchanged.

Ex. When “DOLBY D” is activated.

If the EX/ES (7.1-channel) reproduction mode has been set to “AUTO” or “ON,” one of the EX/ES (7.1-channel) reproduction modes will be activated (see the left column).

For analog sources and digital 2-channel software, you can select one of the following Surround modes. Each time you press SURROUND, Surround modes change as follows:

 

ANALOG

 

L

R LINEAR PCM

PRO LOGIC

SUBWFR

SPEAKERS 1

VOLUME

PL II MOVIE PL II MUSICPRO LOGIC

NEO:6MUSIC NEO:6CINMA

For Dual Mono software, you can select the channel you listen to. (See page 29.)

DUAL

DIGITAL AUTO

LLINEAR PCM

SUBWFR

DIGITAL

SPEAKERS 1

VOLUME

To adjust the speaker output level, see pages 32 and 33.

To cancel the Surround mode

Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote control). “SURR OFF” appears on the display.

37

Page 98
Image 98
JVC RX-8030VBK, RX-7030VBK manual Activating the Surround Modes