Cable Diagrams, Cable ID Chart | Weider 831.159831 manual

CABLE DIAGRAMS

The Cable Diagrams below and on the next page show the proper routing of the Rear Cable (70), the Low Cable

(71), the Press Cable (72), the Butterfly Cable (73), and the Ab Cable (74). The numbers show the correct route

for each Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage the weight system.

CABLE ID CHART	Press Cable (72)
73, 52”		14
70, 95 1/8”		14
70, 95 1/8”
71, 142 1/8”
74, 226 1/2”
72, 387 5/8”		2
72, 387 5/8”
	1
	15
		13
	5	12
	6
8	9
		3
10		11
		7
		4
	30

Image 30

Weider 831.159831 user manual Cable Diagrams, Cable ID Chart, 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8

Contents

SEARS, Roebuck and CO Hoffman ESTATES, IL Model No Serial NoSerial Number Decal Patent Pending Table of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Arm Assembly AssemblyCable Assembly To open the parts bag for that stage Frame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the Short Weight Tube On the bottom Nylon Locknuts yet Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Jamnuts Assembly Bag for identification of the Pro Pulleys Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bracket on Ed as shown Labeled Pulley BAGBracket On the back of the Butterfly Upright Identify the Rear Cable 103 Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright Large tabs Remove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Pulley Direction shownBe removed in step Is attached as shown Identify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley Identify the Press Cable 72. It is approximately Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Pulley and the pin on the Press Top Frame To hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled Seat Adjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PAD Changing the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down LEG LOW Pulley ARM Press Weight Resistance ChartHigh Press LEG Lbs Left Top Troubleshooting and Maintenance Tightening the Cables Hole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No