Arm Assembly |
| 18 | 92 | 11 |
|
| |||
18. Locate and open the parts bag labeled “ARM |
|
| 67 |
|
|
|
| 104 | |
ASSEMBLY.” |
|
|
| |
Press two 2” Square Inner Caps (67) into the |
|
| 13 | Lubricate |
ends of the Leg Lever (13). |
|
|
| |
|
|
|
| |
Lubricate a 3/8” x 3 1/4” Bolt (104). Attach the |
| 67 |
| |
Leg Lever (13) to the Butterfly Leg (11) with the |
|
| ||
|
|
| ||
Bolt and a 3/8” Nylon Jamnut (92). | Do not over- |
|
|
|
tighten the Nylon Jamnut; the Leg Lever must |
|
|
|
|
be able to pivot easily. |
|
|
|
|
19. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg | 19 |
|
| |
Press Lever (14) to the Press Base (3) with the |
|
| ||
|
|
| ||
Bolt and a 3/8” Nylon Locknut (90). | Do not over- |
|
|
|
tighten the Nylon Locknut; the Leg Press |
|
| 14 |
|
Lever must pivot easily. |
|
|
| |
|
|
|
| |
|
|
| Lubricate |
|
|
|
| 88 | 3 |
|
|
|
| |
|
|
|
| 90 |
20. See the inset drawing. Press a Plastic Bushing |
| 20 |
|
|
(60) onto each welded tube on the Press Frame |
|
|
| |
|
|
|
| |
(17). Slide the Pr ess Frame into place on the |
|
|
|
|
Press Base (3). Note: This will be a tight fit. |
|
|
| |
The Plastic Bushings should fit onto each end |
|
|
|
|
of the welded tubes in the Base. |
|
| 106 |
|
Lubricate the 3/8” x 8” Bolt (106). Attach the |
|
| 17 | |
|
| 3 | ||
Press Frame (17) to the Press Base (3) with the |
|
| ||
|
| 17 | ||
Bolt and a 3/8” Nylon Jamnut (92). | Do not over- |
|
| |
|
|
| ||
tighten the Nylon Jamnut; the Press Frame |
|
| Lubricate | 92 |
must pivot easily. |
|
| ||
|
|
|
| 60 |
21. Press a 1 3/4” Square Inner Cap (68) into the top | 21 |
|
| |
of a Press Arm (18). Press a 1” Round Inner Cap |
|
| ||
|
|
| ||
(66) into the Press Arm. |
|
| 18 |
|
Attach the Press Arm (18) to the Press Frame |
|
|
|
|
(17) with two 5/16” x 2 1/2” Bolts (87) and two |
|
|
| |
5/16” Nylon Locknuts (86). |
|
|
| 68 |
|
|
|
| |
Repeat this step with the other Press Arm (18). |
|
|
|
|
|
|
|
| 87 |
|
|
|
| 18 |
|
|
| 86 | 66 |
|
|
|
| |
|
|
|
| 17 |
12
