Official Weider Home Gym Manual & Parts Information - www.weiderfitness.com

Model No. 831.159831

Serial No.

The serial number is found in the location shown below. Write the serial number in the space above.

Serial

Number

Decal

SEARS, ROEBUCK AND CO.

HOFFMAN ESTATES, IL 60179

CAUTION

Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.

USER’S MANUAL

Patent Pending

Visit our website at

www.weiderfitness.com

new products, prizes, fitness tips, and much more!

Image 1

Weider 831.159831 user manual Model No Serial No, Serial Number Decal, SEARS, Roebuck and CO Hoffman ESTATES, IL

Contents

Serial Number Decal Model No Serial NoSEARS, Roebuck and CO Hoffman ESTATES, IL Patent Pending Table of Contents Important Precautions Before YOU Begin Using the Power Stack weight systemDecal Cable Assembly AssemblyArm Assembly To open the parts bag for that stage Locate and open the parts bag labeled Frame AssemblyTape over the head of each Bolt 109 Onto the Bolts. Do not tighten the Nylon Locknuts yet100 Do not Tighten the Nylon Locknuts yet YetLocknuts 86. Do not tighten the Nylon Locknuts yet On bottom Press a 2 Square Inner Cap 67 into the Press Top FrameInto On the bottom On the Short Weight Tube Locknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as shown in stepNylon Locknuts yet Nylon Jamnuts Assembly Pulley BAG 2. Remove one V-Pulley Pages 30 Identify the Butterfly CableBag for identification of the Pro Pulleys Bracket on Bracket On the back of the Butterfly Upright Labeled Pulley BAGEd as shown Identify the Rear Cable Pulley and the pin on the Upright Identify the Ab Cable 74. It is approximately103 Large tabs Groove of the Pulley Remove the 3 1/2 Pulleys 35 from the otherMake sure Be removed in step Direction shownPulley Is attached as shown Hold the Cable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyCable in the groove of the Pulley With the 3/8 Nylon Jamnut Cable Trap 38 to the 3/8 x 4 3/4 BoltIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top Frame Wrap the Press Cable 72 around a V-Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Pulley onto the 3/8 x 4 3/4 Bolt Route the Press Cable 72 through the Press102 3835 With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat Assembly ADJUSTMENTS, beginning on the following Adjustment Pin 40. Note The lip onLeg Press Plate 16 must be on the upper edge Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PAD To change the setting of a weight stack, insert a Changing the Weight SettingWeight stack. Turn the bent end down High Press LEG Weight Resistance ChartLEG LOW Pulley ARM Press Lbs Left Top Tightening the Cables Troubleshooting and Maintenance Hole with the Bolt, Washer, and Nylon Locknut 104 Cable ID Chart Cable Diagrams70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No