JVC RX-888VBK manual Sound control section Amplifier, CD player-changer, Tuner

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 36) in addition to the connections using cables with RCA pin plugs (see pages 5 and 6).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel or the menu function to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 12.)

•Refer also to the manuals supplied with your components.

Sound control section (Amplifier)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

SURROUND ON/OFF: Turns on or off the Surround modes — Dolby Pro Logic, Dolby Digital, and DTS Digital Surround.

SURROUND MODE: Selects the DSP modes.

After pressing SOUND (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations:

SEA MODE:	Changes the SEA modes.
SUBWOOFER – / +: Adjusts the subwoofer output level.
CNTR – / +:	Adjusts the center speaker output level.
REAR•L – / +:	Adjusts the left rear speaker output level.
REAR•R – / +:	Adjusts the right rear speaker output level.
EFFECT:	Selects the effect level.
TEST:	Turns on or off the test tone output.

		STANDBY		ON
		TV/CATV/DBS		VCR 1
		POWER		POWER
DVD	DVD MUILTI	CD	TAPE/MD
TV/DBS	VIDEO	PHONO		FM/AM
VCR 1	VCR 2 ANALOG/DIGITAL			SLEEP
SURROUND	CNTR TONE		CNTR
ON/OFF	1	2		3
			MENU
SURROUND	TEST		REAR-L
MODE	4	5		6
			ENTER
DISC	EFFECT		REAR-R
	7/P	8		9
SOUND	SEA MODE	SUBWOOFER
	10	0		+10
	RETURN	FM MODE/MUTING		100+

	AUDIO/
	TV/VCR
MENU
	CATV/DBS
	SET
EXIT	TEXT
	DISPLAY

TV VOL	CHANNEL		VOLUME
TV/VIDEO	VCR 1	TAPE	MUTING
	CONTROL
/REW	PLAY		FF/
DOWN	TUNING		UP
REC	STOP		PAUSE

RM-SRX888J REMOTE CONTROL

AUDIO/

TV/VCR

CATV/DBS

Check to see if its remote control mode selector is set to the correct position.

To operate the audio system, TVs, and VCRs,

set it to “AUDIO/TV/VCR.”

CNTR TONE: Selects the center tone.

Note:

After adjusting sounds, press the corresponding source selecting button or DISC to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

CD player

After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the CD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or
¢:	previous) track.
	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.
1 – 10, +10:	Selects a track number directly.
	For track number 5, press 5.
	For track number 15, press +10, then 5.
	For track number 20, press +10, then 10.
	For track number 30, press +10, +10, then 10.

CD player-changer

After pressing DISC (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a CD player-changer:

Tuner

After pressing FM/AM (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations:

FM/AM: Alternates between FM and AM.

1 – 10, +10: Selects a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

TUNING UP/TUNING DOWN:

Tunes into stations.

FM MODE/MUTING: Changes the FM reception mode.

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous)
¢:	track.
	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.
1 – 6, 7/P:	Selects the number of a disc installed in a CD
	player-changer.

After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the CD player-changer:

1 – 10, +10: Selects a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5.