JVC RX-888VBK manual Turntable, Cassette deck, MD recorder, VCR 1 VCR connected to the VCR 1 jacks

Turntable

After pressing PHONO (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a turntable:

PLAY:	Starts playing.
STOP:	Stops operations.

Cassette deck

After pressing TAPE/MD or TAPE CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a cassette deck:

PLAY:	Starts playing.
1:	Fast winds the tape from right to left.
`:	Fast winds the tape from left to right.
STOP:	Stops operations.
PAUSE:	Pauses playing. To release it, press PLAY.

ƒREC: Press this button with the PLAY button to start recording.

Press this button with the PAUSE button to enter recording pause.

MD recorder

After pressing TAPE/MD or TAPE CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the MD recorder:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous)
¢:	track.
	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.

ƒREC: Press this button with the PLAY button to start recording.

Press this button with the PAUSE button to enter recording pause.

VCR 1 (VCR connected to the VCR 1 jacks)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

VCR 1 POWER: Turns on or off the VCR 1.

After pressing VCR 1 or VCR 1 CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:

1 – 9, 0: Selects the TV channels on VCR.

PLAY: Starts playing.

1: Rewinds a tape.

`: Fast winds a tape.

STOP: Stops operations.

PAUSE: Pauses playing. To release it, press PLAY.

ƒREC: Press this button with the PLAY button to start recording.

Press this button with the PAUSE button to enter recording pause.

CHANNEL +/–: Changes the TV channels on the VCR.

Note:

You can use either VCR 1 button or the VCR 1 CONTROL button to activate the buttons listed above. If you press VCR 1, the playing source also changes. On the other hand, if you press VCR 1 CONTROL, the playing source does not change.

DVD player

After pressing DVD or DVD MULTI (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a DVD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous) track.
¢:	Skips to the beginning of the next track.
STOP:	Stops playing.

PAUSE: Stops playing temporarily. To release it, press PLAY.

Note:

You can use either TAPE/MD button or the TAPE CONTROL button to activate the buttons listed above. If you press TAPE/MD, the playing source also changes. On the other hand, if you press TAPE CONTROL, the playing source does not change.

IMPORTANT:

After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.	TEST
Note:	4

For detailed menu operations, refer to the instructions supplied with the discs or the

DVD player.

CNTR

2 3

MENU

REAR-L

56

ENTER

REAR-R

8

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK terminals (see page 42) in addition to the connections using cables with RCA pin plugs (see pages 6 and 7).

•Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR

1jacks is set to code “A.”

•When using the remote control:

–For the DVD player and VCR operations, aim the remote control directly at the remote sensor on each component, not on the receiver.

–For the TV operations:

7If the TV having the AV COMPU LINK terminal “RECEIVER/ AMP,” aim the remote control directly at the remote sensor on the receiver.

7If the TV having the AV COMPU LINK terminal “AV COMPU LINK EX,” aim the remote control directly at the remote sensor on the TV.

TV

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

TV/CATV/DBS POWER: Turns on or off the TV.

TV VOL +/–: Adjusts the volume.

TV/VIDEO: Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a TV:

CHANNEL +/–: Changes the channels.

1 – 9, 0, 100+: Selects the channels.

RETURN: Alternates between the previously selected channel and the current channel.