JVC RX-DP9VBK Activating the DSP Modes, Headphone Mode, Without connecting the surround speakers

ALL Channel Stereo mode (ALL CH STEREO)

This mode can reproduce a larger stereo sound field using all the connected (and activated) speakers. This mode cannot be used

without connecting the surround speakers.

•The CENTER CHANNEL submenu settings and the DSP PARAMETER submenu settings cannot be applied to All Channel Stereo mode. (You cannot adjust them for this mode.)

•If headphones are connected or if the front speakers are deactivated, “ALL CH STEREO” cannot be selected (see “HEADPHONE mode” below).

Stereo Film and Monaural Film modes

In order to reproduce a more acoustic sound field in your listening room while viewing stereo sound or monaural sound video software (analog and 2-channel digital signals), you can use these modes. The surround effect will be added, and the sound localization of actor’s words will be improved.

STEREO FILM : To play back stereo video software

MONO FILM : To play back monaural video software

When “STEREO FILM” or “MONO FILM” is used, sounds come out of all the connected (and activated) speakers.

3D THEATER

Only using the front speakers, this mode gives you such a true and clear surround effect only as is reproduced through the Dolby Surround decoder, which is widely used to reproduce sounds with a feeling of movement like those experienced in movie theaters.

•When “3D THEATER” is used, the DSP and 3D-PHONIC indicators light up. The PRO LOGIC indicator also lights up when 2-channel software is played back. (Dolby Pro Logic decoder is activated.)

•If the center speaker is connected (and activated):

Sounds created by the built-in DSP (Digital Signal Processor) come out of the center speaker to localize the sounds. So, you can feel as if actors on the screen actually speak in your room.

•If headphones are connected, “3D HEADPHONE” will be activated. (See “3D HEADPHONE Mode” on page 40.)

HEADPHONE Mode

You can also enjoy the DSP effect (except All Channel Stereo mode) through the headphones.

By pressing DSP MODE when the headphones are connected, HEADPHONE mode is activated without respect to the type of software played back.

The DSP and HEADPHONE indicators also light up.

Activating the DSP Modes

Perform the basic settings and adjustments using the Setup and Adjustment Menus first (see pages 26 to 38).

Activating one of the DSP modes for a source automatically recalls the memorized settings and adjustments done on the above menus.

IMPORTANT:

•When using the remote control:

Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode for a while (10 or 5 seconds).

STANDBY ON

TV/CATV/DBS VCR 1

STANDBY/ON STANDBY/ON

Ex. When you press DSP MODE.

•When using the unit:

Press DOOR DOWN to use the buttons inside the front door.

DOOR

DOWN

	RX-
	DP9V
AUDIO/VIDE
NTROL	RECEIVER

To close the front door, press DOOR UP.

1.Select and play any sound source.

2.Press DSP MODE repeatedly until the DSP mode you want appears on the display.

DSP

DSP MODE

MODE

On the unit	On the remote control
(inside the front door)

The DSP indicator also lights up on the display.

•Each time you press the button, the DSP modes change as follows:

=LARGE HALL 1 = LARGE HALL 2 = RECITAL HALL

=OPERA HOUSE = CHURCH = LIVE CLUB

=DANCE CLUB = PAVILION = ALL CH STEREO*

=LARGE THEATER = SMALL THEATER

=STEREO FILM* = MONO FILM* = 3D THEATER

=SURROUND OFF (DSP off) = (Back to the beginning)

*When multichannel signals come in, you cannot select “STEREO FILM” and “MONO FILM.”

Continued on the next page.

44