KEF Audio KIT100 installation manual Pre-programmed remote control, KEF services

pre-programmed remote control

DEVICE

The remote control will operate the KIT100 DVD Home Theatre System when you press the DVD device key.The other device keys can be set to operate other equipment and are selected by pressing the required device key.The alternative key functionality of the remote control can be seen in “Remote control alternative keys functionality table” on page 46.

In order to record on aVCR it is necessary to press both the record (OPEN/CLOSE) and PLAY keys at the same time.

If the batteries are replaced in the remote control within five minutes then the programmed IR codes will be remembered. If the batteries are removed for longer the remote may need to be re- programmed.

	Quick programming the remote control
	In the user manual for the equipment you wish to program, you should find a 3 or 4 digit product IR
	code. If this is not given then look up the 4 digit code in the “Equipment manufactures IR codes
	table” on page 39 for the brand of equipment that you have. If there are several product IR codes
	then you will need to try them in turn until successful operation is achieved. Follow the quick
	programming sequence below. If a key is not pressed for 10 seconds then the programming process
	will stop automatically, and you will have to start again.To exit the programming mode press any
SOURCE	DEVICE key so that the LED turns off.
	1. obtain the product IR four digit code(s) from the table
	2. press and hold the SET key and the required device key (TV,VCR, SAT or CBL) together until
	the LED turns on
	3. enter the four-digit code for your equipment using the numerical keys, the LED will blink for
	each digit, the LED should then turn off.
	If the LED flashes two times, to indicate that an invalid code was entered, then repeat step 3.

4.test the remote control with your equipment and if not successful, look up the next product IR code for your equipment's manufacturer and repeat the steps from 2.

Automatic search programming

If the products IR three or four digit code is not in the equipment manual or the “Equipment manufactures IR codes table” on page 39, or still dose not work correctly after completing the Quick programming steps above for all the listed codes, then you can get the remote control to automatically scroll through all the IR codes for each specific device type. Patience will be required as it can take several minutes for the remote control to go through each of the codes for that device type. Follow and repeat the automatic programming sequence below. If no key is pressed on the remote control for 30 seconds then the programming process will stop automatically, and you will have to start again.

1.turn on the equipment you wish to operate with the remote control (if the equipment is aVCR then insert a tape and start playback) and ensure that the remote control remains pointing at the equipment

2.press and hold the SET key and the required device key (TV,VCR, SAT or CBL) together until the LED turns on

3.press and release the SET key again to enter the search mode, the LED will flash fast

4.Press and hold the POWER key for 3 seconds until the LED flashes every 2 seconds.This indicating that you are in the automatic search mode where a different IR code is transmitted automatically on each flash.

5.when your equipment turns off because it has received the correct power IR command, immediately press any key to stop the automatic search, the LED stops flashing

6.press any device key (TV,VCR, SAT or CBL) to store the current IR code, the LED will turn off

7.turn your equipment back on, press the correct device key (TV,VCR, SAT or CBL) and test the remote control for correct functionality. If it does not work fully then repeat the steps from 1.

8.If the remote controls LED turns off before your equipment receives a valid IR code to turn it off then repeat the above steps from 1 ensuring that the remote control is pointing at the equipment, that the equipment is switched on and that you chose the correct DEVICE type.

Reading the stored IR code

You can see what IR code is stored for each device key. Press the relevant device key (TV,VCR, SAT or CBL).Then press and hold SET and at the same time press digit 1, 2, 3 or 4 on the numeric keys, then release all keys. Each time you press SET and digit “1” to “4” the LED will flash the same number of times as that digit of the IR code number.

KEF services

Customer service

For additional help in solving problems, follow the trouble shooting section then contact KEF® customer service or your local retailer.

Warranty

The KEF Instant Theatre system is covered by a limited non-transferable warranty. Details of the warranty are provided on the warranty card that came with your system. Please fill out the information section on the card and return it.

Accessories

The KEF Instant Theatre system shelf speakers are compatible with the optional KEF Instant Theatre speaker floor stands.

20