5.Close the washer lid. The washer will not operate with the lid open.
6.Turn the Water Level selector to the correct setting for your wash load and the type of fabric being washed.
•Choose a water level that allows the load to move freely for best fabric care. See "Loading."
•You may change to a higher level setting after the washer has started filling by turning the knob to a different setting.
7.Set the Water Temperature selector to the correct setting for the type of fabric and soils being washed. Use the warmest wash water safe for fabric. Follow garment label instructions.
Water Temp | Use for |
|
| |
Hot | Whites | and | pastels | |
| Heavy | soils |
|
|
Warm | Bright | colors |
| |
| Moderate to light | soils | ||
Cold | Colors | that | bleed | or fade |
| Light soils |
|
| |
NOTE: In wash water temperatures colder than 70°F (21°C), some detergents do not dissolve well. Soils can be difficult to
10.Push in the Cycle Selector Control (Timer) knob and turn it to the wash cycle you want. Reduce the wash time when using a small load size setting. See "Selecting a Cycle and Time."
Pull out the Cycle Selector Control (Timer) knob to start the washer
To stop or restart your washer
•To stop the washer at any time, push in the Cycle Selector Control (Timer) knob.
•To restart the washer, close the lid (if open) and pull out the Cycle Selector Control (Timer) knob.
This section describes the available wash cycles and will help you make the best cycle selections for your wash loads. Each
cycle is designed for different types of fabric and soil levels.
•The washer pauses briefly throughout each cycle. These pauses are normal. Refer to "Normal Sounds" to learn more about the sounds you may hear during a wash cycle.
•Refer to "Understanding Washer Cycles" to learn what happens during a wash cycle.
NOTE: Use this control to choose agitation time and to start the washer. For heavy soil and sturdy fabrics, use the full time. Use less time for light soil and delicate fabrics.
2ND RINSE
PERMANENTPRESSI
remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small
(OPTIONAL) An Automatic Temperature Control (ATC) electronically senses and maintains a uniform water temperature by regulating incoming hot and cold water.
_RJE_ WAMI
ULTRACLEAN
•Even in cold wash, some warm water is let into the washer to maintain a minimum temperature of approximately 70°F (21°C).
•Warm wash is maintained at approximately 90°F (32°C).
•Warm rinse is maintained at approximately 70°F (21°C) for all warm rinse settings. To reduce wrinkling, the warm rinse is regulated to be cooler than the warm wash.
8.(RINSE OPTIONS) You can customize your wash by adding rinse Options to your cycle selections. A cycle will "start" where you set the Cycle Selector Control (Timer) knob. See "Selecting a Cycle and Time." The cycle will "stop" where you set the Options Control knob. This knob has settings for:
•One Rinse. Use this option for one rinse after a basic wash cycle, Rinse & Spin, and Drain & Spin.
•2nd Rinse. A 2nd Rinse can be added to the Ultra Clean and Whitest Whites cycles.
9.Set the Speeds Control knob according to the type of fabric in the load. See "Selecting Wash/Spin Speeds."
p_SHa,_IJRN_SEr I_IJ.TO_'ART p[ISH_'Up
Cycle Selector Control (Timer)knob
CATALYS'P Cleaning Action
Your washer uses the CATALYST' Cleaning Action to help ensure better soil and stain removal from your wash load. CATALYST" Cleaning Action reduces the need for pretreatment and is safe for all fabrics. CATALYST'Cleaning Action is available in the Whitest Whites and the Ultra Clean cycles. Although CATALYST _Cleaning Action is available on all speed control settings, for the best cleaning performance, use this selection with the Heavy Duty speed selection.
NOTE: To add CATALYST" Cleaning Action to your wash cycle, you must set the Cycle Selector Control (Timer) knob on the blue oval labeled Catalyst_%
12
