Kenmore 110.2403# manual Installation Requirements, Parts supplied, Alternate Parts, You will need

INSTALLATION REQUIREMENTS

Assemble the necessary tools and supplies before beginning the washer installation. The paris supplied are in the washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

•Pliers that open to 19/16in. (3.95 cm)

•Flashlight (optional)

Parts supplied:

3 4 5

1.Drain hose

2.Silver, double-wire hose clamp (for the bottom of the drain hose)

3.Yellow, single-wire hose clamp (for the top of the drain hose)

4.Water inlet hoses (2)

5.Flat water inlet hose washers (4)

Tools needed for securing the drain hose and leveling the washer:.

•Adjustable or open end wrench %8in. (14 mm)

•Level

•Wood block

•Ruler or measuring tape

Parts supplied:

12

1.Shipping strap with fastener

2.Front leveling feet with nuts (2)

Alternate Parts

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOME® (1-800-469-4663).

If You Have:		You Will Need to Buy:
Laundry	tub or	Sump pump system	(if not already
standpipe	taller	available)
than 96 in. (2.4 m)
1 in. (2.5 cm)		2 in. (5 cm) diameter	to 1 in. (2.5 cm)
diameter		diameter standpipe	adapter,
standpipe		Part No. 3363920

If You Have:		You Will Need to Buy:
Overhead sewer		Standard	29 gaL (76 L) 39 in. (99 cm) tall
		drain tub or utility sink, sump pump and
		connectors		(available from			local
		plumbing	suppliers)
Floor drain		Siphon break, Part Number					285320;
		additional	drain		hose,
		Part Number 3357099 and connector
		kit, Part Number			285442
Water faucets		2 longer water fill hoses:
beyond reach of		6 ft (1.8 m) Part Number				76314,
fill hoses		10 ft (3.0 m) Part Number				350008
Drain hose	too	Drain hose,		Part No. 388423 and hose
short		kit, Part No.		285442
Drain hose	that is	Hose kit, Part No. 285442
too long
Lint clogged	drain	Drain protector,			Part No.	367031

,,,eta O e e }l s

Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. See "Drain System."

iMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

•A water heater set to deliver 120°F (49°C) water to the washer.

•A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements."

•Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-199 psi (34.5-690 kPa). Washers with triple dispensers require 20-199 psi (138-699 kPa) for best performance.

•A level floor with a maximum slope of 1 in. (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.

•A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause

damage in low temperatures. See "Washer Care" for winterizing information.