Kenmore 1T6.29429 manual Open auctioncontrol

Review this chart to find do-it-yourself solutions for minor performance problems. Any ser- vice needed, other than those described in this owner's manual, should be performed by an authorized service representative.

........... Failure to do so co, ul,,?'resu, l,l,,in electrical sho?,k ?,,[,,,,perso?,,?I injury_

Cleaner won't start-

Poor job of dirt pick-up.

Cleanerstarts but cuts off°

I.Unplugged at wall outlet,

2.Tripped cimuil breaker/blown fuse at household service panel

3+ Loose hose electrical connections

4,, Tripped overload protector in

POWER-MATE TM.

1+ Full or clogged dust bag.

2.Clogged airflow passages

3+ Dirty motor safetyfilter

4_ Wrong pile height setting

5.Open auctioncontrol

6.Hole in hose

7, Worn POWER-MATETMbrushes

8.Worn or broken belt

9.Dirty brush or brush supports 10, Canister hood open

'L Hose or hood electrical connections

Tripped overload proteclor in

POWER.MATEm,,

Trippedoverloadprotector in canister

1.Plug in firmly, push ONtOFF switch to ON

2.Reset circuit breaker or replace fuse

3.Reconnecthose ends, (page 7)

4.Clean brush and brush supports, then reset, (pages 14, 15)

1. Change bag, (page 12)

2o Clear airflow passages, (page 12)

3.Clean filter, (page 13).

4.Adjust setting, (page 9),

5+ Adjust control,(page 11)

6.Replace hose

7.Change brushes, (page 16},

8 & 9+ See BELT CHANGING AND BRUSH

CLEANING, (pages 14, 15)+

10.Close and latch hood_

1.Check connections,reconnect hose ends,(page 7).

2+ Removeany items thatmay be caught orjammed, thenreset. If cleanerstarts and stops again+cleanbrush and brush supports, then reset,(pages"_4,_,5)

3.Change dust bag, clearairflowblockage, (page 12). Wait 20 minutesfor motor to cool andautomatically reset.

POWER-MATETMwill not	1.	POWER-MATE TM connections
run when attached.	2.	unplugged.
		Worn or broken belt.
	3, Dirty brush or brush supports
	4.	Tripped	ovedoad protecior in
		POWER-MATE _'-
Performance indicator,	Io	Furlor clogged dust bag
some models,is red,	2_ Dirty filter
	3.	Cloggedairflow passage.
	4,	Certain attachmenttools
Cleanerpicks up moveable	t.	Wrong	pile height setting
rugs ,or- POWER-MATETM	2.	Suction	too strong
)ushee too hard,
Light won'twork.	1.	Burned outlight bulb
Cord wor_'trewind+	1,	Dirty power cOrdr
	2o Cordjammed.
Cleanerleaves marks	I+	Wrong vacuumingpattern
on carpet

Plug in firmly, (page 6).

2&3o See BELT CHANGING AND BRUSH

CLEANING, (pages 14, 15).

4+ Check brush area for excessive lint build-up or jamming CIean brush and brush supports, then reset, (pages 14, 15)

1+ Change bag, (page t2)

2.Change tiller, (page 13)

3.Clear clog from airflow passage, (page 12)

4+ This is normal Light should go off when loo_is removed

1. Adjust setting, (page 9)

2+ Open suctioncontrol,(page 11)

1+ Change light bulb, (page 14)

1.Clean the powercord

2, Pull oulcordand rewind

1_ SeeVACUUMING"rIPS,(page 9)..

17