Install 3-Valve Bypass | Kenmore 300 Series, 300 Series specification

Install Plastic Bypass Valve

Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port.

Turbine	Sensor Port
Support

Turbine

FIG. 10

INSTALLING HOLDING CLIPS

	Bypass Valve or	Black Clip	Cross Section of Valve
		Black Clip	Inlet or Outlet

	Installation Adaptor
	Installation Adaptor

O-Ring

Clip Snaps into Place

Between Larger Diameter Rings

FIG. 11

BYPASS VALVE TURNED DOWNWARD

Turn bypass valve upside down to connect to floor level plumbing.

OUT

IN

FIG. 12

Install 3-Valve Bypass

INSTALLING 3 VALVE BYPASS AND PIPES

3 VALVE BYPASS

Complete the following steps to install the three (3) valve bypass:

•Cut the house main water pipe where you will con- nect the softener.

•Loosely put together pipe, fittings, and the three

(3) valves.

•Place valve(s) within easy reach.

When all pipe, fittings and valves make a good fit together, tighten all threaded joints (use pipe dope on outside threads), or solder all sweat joints.

TO	FIG. 13
Softener Inlet

Questions? Call The Kenmore Water Line 1-800-426-9345

12

Image 12

Kenmore 300 Series, 300 Series warranty Install 3-Valve Bypass, Installing Holding Clips, Bypass Valve Turned Downward

Contents

Repair or Parts ? Call toll free Save this Manual ONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksDisclaimer of implied warranties limitation of remedies Table of Contents Facts and Figures to Keep Safety Guides Unpack and Check Your Carton Parts DescriptionsSmall Parts Inspect Shipment Plan Your Installation Proper Order to Install Water Treating EquipmentPlan Your Installation Tools Needed Typical Installation Where to Install the Water Softener Suggested Slab Foundation Installation Draw in Your Pipes and Fittings OUT PIPE, FITTINGS, Other Materials Needed Read Before Beginning Installation Before Installing Checks & Tests Install Plastic Bypass Valve Assemble Inlet Outlet ADAPTORS, or Plastic Bypass ValveBypass Valve Install 3-Valve Bypass Installing Holding ClipsInstalling 3 Valve Bypass and Pipes Valve Bypass Locate Water Softener and Connect Pipes Move Softener Into PlaceTypical Soldering Connections Position Softener Into Place Connect Valve and Salt Tank Drains Connect the Valve Drain HoseConnect Salt Tank Overflow Tubing Leak Test House Main Water Shutoff ValvesSingle Bypass Leak Test Water Meter Jumper Wire Connecting TransformerElectrical Requirements Cold Water Pipe Grounding Install Covers and Restart Water Heater Install CoversInstall Covers Restart the Water Heater Program The Timer Program the TimerSET Present Time of DAY SET Water Hardness Number SET Regeneration TimeSET Salt Level Sanitize The Water Softener Sanitize the Water SoftenerSanitize Your Water Softener AS Follows Adding Salt To The Storage Tank Adding Salt to the Storage TankWater Softening Salt with Iron Removing Additives Check List of STEP-BY-STEP Guides to Install Check List Faceplate Timer Features Extra RechargeRecharge NOW Recharge Tonight Efficiency Mode Error CodeTo turn this setting on Program Memory Water Flow Through Softener in Service Soft Water Service and RegenerationHow Your Water Softener Works Water Flow Through Softener in Fill Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in Backwash Water Flow Through Softener Fast Rinse Automatic BypassElectronics Care Of Your Water Softener Salt BridgeSalt Bridge Keeping the Water Softener Clean Iron from Resin BEDNozzle & Venturi Drain ALL Water from Softener Protect the Water Softener from Freezing Problem Cause Correction Checklist to Help YOU Save Money Specifications Model 38306 Timer Code S Model 39306 Timer Code SBypass Valves Inches Other Specifications Service Tech Information Wiring SchematicFaceplate Always Make These Initial Checks First Procedure for Removing Error Code from Faceplate Possible Defect Code Troubleshooting Valve Position Indicators Timer PWA ReplacementOther Information Model Brine Valve Float Setting Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Rotary Valve Service DisassemblyAssembly To Relieve Pressure Water Flow Through the Softener Valve Service Cycle Fill CycleBrining and Brine Rinse Cycle Water Flow Through the Softener Valve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse Cycle Questions? Call The Kenmore Water Line Exploded View Parts List Water Softener CompletePart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours