Kenmore 153.336465, 761 Start Up Conditions, Thermal Expansion, Expansion Tank Sizing Chart

Start Up Conditions

Thermal Expansion

Property Damage Hazard

•Avoid water heater damage.

•Install thermal expansion tank or device if necessary.

•Contact qualified installer or service agency

Water supply system may, because of such events as high line pressure, frequent cut-offs, and the effects of water hammer have installed devices such as pressure reducing valves, check valves, back flow preventers, etc., to control these types of problems. When these devices are not equipped with an internal by-pass, and no other measures are taken, the devices cause the water system to be closed. As water is heated, it expands (thermal expansion) and closed systems do not allow for the expansion of heated water.

The water within the water heater tank expands as it is heated and increases the pressure of the water system. If the relieving

point of water heater's temperature-pressure relief valve is

reached, the valve will relief the excess pressure. The

temperature-pressure relief valve is not intended for the

constant relief of thermal expansion. This is an unacceptable condition and must be corrected.

It is recommended that any devices installed which could create a closed system have a by-pass and/or the system have an expansion tank or device to relieve the pressure built by thermal expansion. Thermal expansion tanks are available from Sears stores and through the Sears Service Centers. Contact the local plumbing inspector, water supplier and/or the Sears Service Center for assistance in controlling these situations, see Figure 26.

Thermal Expansion Tank Specifications

	Tank	Dimensions		Pipe
Model	Capacity	in Inches		Fitting
Number	In Gallons	Diameter	Len_lth	On Tank
153.331020	2	8(203mm)	12-3/4(323mm)	3/4"Male
153.331050	5	11(279mm)	14-3/4(375mm)	3/4"Male

Expansion Tank Sizing Chart

Inlet* Water Heater Capacity (Gallons',

Water

	Pressure	30	40	50	66	80
Expansion	4Opsi	2	2	2	5	5
Tank	5Opsi	2	2	2	5	5
Capacity	6Opsi	2	2	5	5	5
Needed	7Opsi	2	2	5	5	5
	8Opsi	2	5	5	5	5

*Highest recorded inlet water pressure in a 24 hour period or regulated water pressure.

NOTE: Expansion tanks are pre-charged with a 40 psi air charge. Ifthe inlet water pressure is higher than 40 psi, the expansion tank's air pressure must be adjusted to match that pressure, but must not be higher than 80 psi.

		WATER	HEATER	(3)
		COLD	WATER	PRESSURE
HOT	COLD	INLET	FITTING	REDUCING
				VALVE WITH
				BY-PASS

			WATER SHUT-OFF
	PRESSURE	GAUGE		INLET	COLD
	RECOMMENDED		INSTALLATION
	(VERTICAL		MOUNTING)
WATER HEATER
COLD WATER
INLET	FITTING		FLOOR, CEILING		JOIST, ETC.
				PRESSURE
	_,,,,.			REDUCING
					13)
				VALVE WITH
/			(1)		BY-PASS
			TANK^^/
		EXPANSION
/	(2)		7		t
				WATER	SHUT-OFF"
	PRESSURE	GAUGE		INLET COLD
	ALTERNATE RECOMMENDED			INSTALLATION

(HORIZONTAL MOUNTING)

FIGURE26,

Strange Sounds

Possible noises due to expansion and contraction of some metal parts during periods of heat-up and cool-down do not represent harmful or dangerous conditions.

Condensation causes sizzling and popping within the bumer area during heating and cooling periods and should be considered normal. See Condensation section.

Draft Hood Operation

Check draft hood operation by performing a worst case depressurization of the building. With all doors and windows closed, and with all air handling equipment and exhaust fans operating such as furnaces, clothes dryers, range hoods and bathroom fans, a match flame should still be drawn into the draft hood of the water heater with its burner firing. If the flame

23