SECTION 1
WATER SOFTENER START UP
C. PROGRAM THE TIMER
SET WATER HARDNESS NUMBER
•Press the SELECT button once again to display
the words SET HARDNESS and a flashing 25.
ness | of your | water | supply | is on | HARDNESS | |
|
|
|
|
|
| |
The | grains | per | gallon | (gpg) | hard- | s£r |
your | water | analysis | report. | Be |
|
sure to enter water test results on page A, for future reference.
If your water supply contains iron, compensate for
it by adding to the water hardness number. For ex- ample, assume your water is 20 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each 1 ppm of iron. In this example, you would use 30for your hard- ness numbel,.
|
| 20 | gpg hardness |
2 ppmironx | 5 = 10 | +10 |
|
| (times) | 30 | HARDNESS NUMBER |
•Press the UP / DOWN buttons to set your water
hardness number in the display. The DOWN button moves the display to 1. The UP button moves the
display to the highest setting (see maximum setting for your model in the specifications).
Note:
Each press of the UP / DOWN button changes the
display by 1 between 1 and 25. Between 25 and the
highest number, the display changes 5 at a
time...25, 30, 35, etc. Holding the UP or DOWNbut- ton in changes the display twice each second.
SET RECHARGE (REGENERATION) TIME
•Press the SELECT button once again to display
the words SET RECHARGE TIME and a flashing 2:00 AM.
At the 2:00 AM | recharge | time | set- | IsEr |
| ||||
ting, | the | softener | begins | regenera- | R_TdAR_ | 1 | |||
tion | (see | pages |
|
| |||||
2:00 | AM, | ending | no later | than | 4:30 |
| L 'LJL! | A_ | |
AM. | This | is a good | time | in most | households | because |
water is not being used (see Automatic Bypass, page
be better for your household, do the following.
• Press the UP / DOWN buttons to set the desired
recharge starting hour. Be sure to observe the AM- PM as you did when setting the present time of day.
Note:
Each press of the UP / DOWN buttons changes the
display 1 hour. Holding the buttons in changes the display twice each second.
SET SALT LEVEL
•Press the SELECT button once again to display
SETSALTLEVEL and a flashing 0 (zero). See Step E,
page
The | face | plate | timer has | a | salt | SETSALTLEVEL | |
monitor | with | an indicator | light | to | F | ||
remind you to add salt to the stor- | |||||||
U | |||||||
age | tank. |
|
|
|
| ||
|
|
|
|
|
Note:
You must set salt level each time salt is added to the water softener.
•To set this monitor system, lift the salt hole cover and level the salt in the storage tank. The salt level decal, on the brinewell inside the tank, has numbers
from 0 to 8. Observe the highest number the leveled salt is at, or closest to. Press the UP / DOWN but-
tons until the number corresponds with the salt lev-
el number. At level 2 or below, the indicator LED
will flash. If you wish to turn this feature off, press
the DOWN button past 0, and the word "OFF" flashes in the display.
• Press the SELECT button once
again, to complete initial pro-
gramming, and the currect time of day will show in the display.
IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE,
NUMBER 1- 800- 426- 9345.
SEE PAGE 2-1 FOR OTHER FACE PLATE TIMER FEATURES.
Problems, | Questions? | Call 1- 800- 426- 9345 Kenmore | Water | Line |