Chapter Two : Setting Up PowerTouch

After you install the batteries or reset PowerTouch, you need to calibrate the touch screen. The touch screen responds to pressure from the included stylus or your finger:

If you are replacing batteries and complete the battery replacement within 3 minutes, you do not need to calibrate the screen; calibration is stored in memory.

If the screen’s performance begins to change, you can recalibrate it without resetting PowerTouch by pressing

on the Setup Preference menu. For more information about accessing this menu, see “Identifying Devices For PowerTouch Control” on page 37.

Calibrating the Touch Screen

To calibrate the touch screen, use the stylus to touch the center of each of the calibration points displayed:

When you touch each calibration point, you should hear a beep and see the next point, indicating that area of the screen is now calibrated. If you do not hear a beep, touch the calibration point until you do.

The touch screen is sensitive to pressure, not to movement. Press firmly but gently on any touch screen element. The screen will not respond if you simply brush the stylus or your finger along the surface.

Resetting PowerTouch

If you want to reconfigure PowerTouch, you can reset it. You do not need to do this unless you experience a prob- lem.

1.Open the cover.

2.Use the stylus to press the blue button at the bottom of

the battery case:

RC-R1110:

RC-R1010:

(For VR-4900/VR-4700)

(For KRF-V9993D)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESET

RESET

The items you set up in this chapter will remain in

 

PowerTouch. If you want to make it to the factory–set de-

33

fault condition, please follow the instructions on page 98/

99 of the Users’ Guide.

Setup Remote

After “Calibrating the Touch Screen”, the “Selecting the Model Type” display appears automatically (Except for KRF- V9993D). (This is not displayed when the model type has already been set.)

Selecting the Model Type

To set the model type:

1.Press the receiver’s ON STANDBY key to turn it ON.

2.Point the PowerTouch to the receiver and press the in the display.

3.The receiver automatically transmits its type code to PowerTouch. When the PowerTouch stores it, the model type selection is complete.

Now the new PowerTouch is available for operation. The “Quick Tour” is the initial display after the batteries have been loaded.

•If the model type cannot be selected automatically be- cause the receiver is not ON, etc., the model type can be selected manually. In this case, refer to the table on the right and select the correct model type in step 2 above.

If you have this receiver...

Use this model

type...

VR-4900

MODEL 1

VR-4700

MODEL 2

 

 

KRF-V9993D

MODEL 3

If you committed mistake in the model type selection, restart it as follows.

•While holding the CONFIRM and VOLUME DOWN keys together, press and release the RESET button under the battery cover (see above diagram). Do not release the CONFIRM and VOLUME DOWN keys until a short beep indicating the completion of setting is heard.

After the above, all settings are reset to the factory set- tings.