Kenwood VR-510 Recording, Recording audio (analog sources), Recording video, Recording audio (digital sources), Recording a music source, Recording music in A-RECor M-RECmode

Recording

Recording audio (analog sources)

26 MONITOR

INPUT SELECTOR

Recording a music source

1Use the INPUT SELECTOR knob to select the source (other than “MD/TAPE”) you want to record.

2Set the cassette deck or MD recorder to record.

3Start playback, then start recording.

Recording tapes or MD (with MONITOR function)

	MONITOR = MD/TAPE recording
	1 Press the MONITOR key.
		FM	AUTO SOUND	DIGITAL
Operations		AM PRO LOGIC S.DIRECT
		MHz 3 STEREO MONITOR
		kHz DOWN MIX DSP
	2 Use the INPUT SELECTOR knob to select a source other than
	“MD/TAPE”.

3Start playback on the cassette deck connected to the MONITOR jacks and start recording on the cassette deck or MD recorder connected to the MD/TAPE jacks.

MD/TAPE = MONITOR recording

1Use the INPUT SELECTOR knob to select “MD/TAPE”.

2Start playback on the cassette deck connected to the MD/TAPE jacks and start recording on the cassette deck connected to the MONITOR jacks.

•To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck.

MONITOR function (analog sources only)

You can connect a cassette deck or graphic equalizer to the MONITOR jacks of the receiver. If a graphic equalizer is connected, the MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the just- recorded signal. For more information, refer to the instruction manual of the connected component.

Recording video

1Use the INPUT SELECTOR to select the video source (other than “VIDEO1”) you want to record.

2Set the video deck connected to VIDEO 1 to record.

• Select the REC MODE to record a digital input source.

3Start playback, then start recording.

•Recording may not be normal for some video software. This is due to the copy guard condition.

Recording audio (digital sources)

Switch on the REC mode to record a digital input source.

Usually use the A-REC(Auto-Record) mode to record audio input sources. When the digital mode changes during recording in the A- REC mode, the audio may be interrupted momentarily.

Recording music in A-REC or M-REC mode

DIMMER

INPUT SELECTOR

1Use the INPUT SELECTOR knob to select the source (CD/DVD, DVD/6ch, VIDEO2, or VIDEO3) you want to record.

2Set the cassette deck or MD recorder to record.

3Press and hold the DIMMER key for more than 2 seconds to select the A-REC or M-REC mode.

• The mode changes every 2 seconds as shown below.

1 Rec mode off : The digital input record mode is switched off.

2A-REC :The digital input signals (DTS, Dolby Digital, or PCM) are identi- fied automatically and converted into stereo signals that are ready

for recording.

3 M-REC :The input signal type at the moment this mode is selected is held throughout this mode.

For A-REC mode:

					DIGITAL
	FM		AUTO SOUND
	AM PRO LOGIC S.DIRECT
	MHz 3 STEREO MONITOR
	kHz DOWN MIX				DSP
	FM		AUTO SOUND		DIGITAL			AUTO
	AM PRO LOGIC S.DIRECT							MEMO
	MHz 3 STEREO				MONITOR			ST.
	kHz DOWN MIX				DSP		TUNED
For M-REC mode:
	FM	AUTO SOUND		DIGITAL
	AM PRO LOGIC S.DIRECT
	MHz 3 STEREO MONITOR
	kHz DOWN MIX				DSP
	FM	AUTO SOUND		DIGITAL			AUTO
	AM PRO LOGIC S.DIRECT						MEMO
	MHz 3 STEREO			MONITOR				ST.
	kHz DOWN MIX				DSP	TUNED

4Play the source from the beginning and start recording.

•If the audio reproduction stops in the middle due to change in the input signals, etc., press the DIMMER key.