15 EN
Preparing for surround sound

Speaker settings

To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
It is not advisable to select “LRG” (large) for front, center, and surround
speakers as this will cause the speakers to malfunction.
1

Turn on the power to this receiver by pressing POWER ON/

STANDBY or POWER key.

2

Press the SET UP key to enter the SET UP mode and use the

MULTI CONTROL knob or Joystick for the following

displays.

1SP SETUP
2TESTTONE
3DISTANCE
4EXIT
The flow of the SET UP is as follows;
SP SETUP TESTTONE DISTANCE EXIT
Front
Center
Surround
Subwoofer
Front
Center
Surround
Subwoofer
Re-mix
L
C
R
SR
SL
SW
L
C
R
SR
SL
SW
MANUAL
AUTO
3

Select a speaker system.

1Select SP SETUP and press the SET UP key again so that the
subwoofer setting indication “SUBW ON” appears.
2Use the MULTI CONTROL knob or Joystick to select the
appropriate subwoofer setting.
1SUBW ON :Subwoofer setting mode to the receiver is ON.
2SUBW OFF:
Subwoofer setting mode to the receiver is OFF.
•The initial setting is “SUBW ON”.
•When the setting “SUBW OFF” is selected, the front speakers
are automatically set to “FRNT LRG” and the procedure skips to
step 6.
Before step 6, press the SET UP key to accept the setting.
•When subwoofer output sound is required, select “FRNT NML”.
3Press the SET UP key to accept the setting.
•The front speakers setting indication “FRNT LRG” appears.
4Use the MULTI CONTROL knob or Joystick to select the
appropriate front speakers setting.
•It is not advisable to select “LRG” (large) for front speaker as this
will cause the speaker to malfunction.
1 FRNT NML (normal):Average size front speakers are
connected to the receiver.
2 FRNT LRG (large) :Large front speakers are connected to
the receiver.
•For “FRNT LRG” selection, no sound will be heard from subwoofer
speaker even when it is set to ON. However, if you select
CINEMA EQ when subwoofer is selected, you will be able to
hear sound from the subwoofer.
When in STEREO mode, the sound goes directly to front speaker.
•ACTIVE EQ will be available only during “FRNT NML” selection.
5Press the SET UP key to accept the setting.
•The center speaker setting indication “CNTR” appears.
6Use the MULTI CONTROL knob or Joystick to select the
appropriate center speaker setting.
•It is not advisable to select “LRG” (large) for center speaker as
this will cause the speaker to malfunction.
If you selected “LRG” as the front speakers setting,
1CNTR NML (normal):An average size center speaker is
connected to the receiver.
2CNTR LRG (large) :A large center speaker is connected to
the receiver.
3CNTR OFF : Center speaker setting mode to the
receiver is OFF.
If you selected “NML” as the front speakers setting,
1CNTR ON : Center speaker setting mode to the
receiver is ON.
2CNTR OFF : Center speaker setting mode to the
receiver is OFF.
7Press the SET UP key again to accept the setting.
•The surround speaker setting indication “SURR” appears.
8Use the MULTI CONTROL knob or Joystick to select the
appropriate surround speaker setting.
•It is not advisable to select “LRG” (large) for surround speaker as
this will cause the speaker to malfunction.
If you selected “LRG” as the center speaker setting,
1SURR NML (normal):Average size surround speakers are
connected to the receiver.
2SURR LRG (large) :Large surround speakers are connected
to the receiver.
3SURR OFF :Surround speaker setting mode to the
receiver is OFF.
MULTI CONTROL
SET UP
SET UP
POWER
POWER
ON/STANDBY
Joystick
(MULTI
CONTROL 5/∞)
Continued to next page
*5228/15-18/EN 14/06/2002, 11:58 AM15