16 EN
Preparing for surround sound
If you have selected other than “LRG” as the center speaker
setting,
1SURR ON : Surround speaker setting mode to the receiver is
ON.
2SURR OFF :Surround speaker setting mode to the receiver is
OFF.
9Press the SET UP key again to accept the setting.
•The subwoofer re-mix setting indication “SW RE-MIX” scrolls
across the display.
“SW RE-MIX” scrolls across the display.
•If subwoofer is turned OFF, subwoofer re-mix setting is not
visible.
0Use the MULTI CONTROL knob or Joystick to select the
appropriate subwoofer re-mix setting.
1 RMX ON :Subwoofer re-mix set mode to the receiver is ON.
2 RMX OFF : Subwoofer re-mix set mode to the receiver is OFF.
!Press the SET UP key to accept the setting.
•The receiver enters the speaker volume level adjustment
mode.
•In step 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
4
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1Press the SET UP key to begin TEST TONE.
1AUTO
2MANUAL
2The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Joystick.
Press the SET UP key again to select either AUTO or MANUAL.
Use the MULTI CONTROL knob or Joystick to adjust the
volume level of the test tone output from the speaker channel
to be adjusted.
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
The channel indication blinks while the test tone is being ouput.
•If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. ∞
•If the speaker setting selects are OFF, the speaker level settings
are reset.
3Press the SET UP key.
•The test tone is turned off. The receiver enters the mode for
inputting the distance to the speakers.
4For MANUAL selection, press the SET UP key each time to
select the speaker channel.
5
Input the distance to the speakers.
1Select the DISTANCE from the set up displays and press the
SET UP key again.
2Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers : ____ feet (meters)
Distance to center speaker :____ feet (meters)
Distance to surround speakers : ____ feet (meters)
3Use the MULTI CONTROL knob or Joystick to select the
distance to the front speakers.
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
•The allowable setting range is 1 to 30 feet (0.3m to 9.0m),
adjustable in 1 foot (0.3m) increments.
4Press the SET UP key to accept the settings.
5Repeat steps 3 and 4 to input the distance for each of the
speakers.
6Setup is complete when the input indication appears.
•The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
7Press the SET UP key to exit the SET UP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
1Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
•You can store a separate input level for each input source.
2Press the SOUND key repeatedly until the “INPUT” indication
appears.
3Use the MULTI CONTROL knob or Joystick to adjust the input
level.
•The adjustment mode is displayed for approximately eight
seconds.
•The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4Press the SOUND key again to return to the input indication.
*5228/15-18/EN 14/06/2002, 11:58 AM16