Kicker SX1250.1, SX650.1 manual Lo-Pass Hi-Pass, Phase, Memory Presets

Operation

Memory Presets

There are four memory preset keys each with an indicator above it in the ISIS VFD display. The indicator will illuminate if that

STORING A PRESET

Make all the adjustments you want to have stored in the preset and return to the DEFAULT screen.

PRESET PRESETS

Ok, we know that sounds like a certain pizza commercial, but seriously the four memory presets come with settings already in them.

In more general terms, each preset offers you these options.

Memory-1sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz and an infrasonic filter (often

Operation

memory preset is currently in use.

To store your settings into a preset simply press and hold the desired

HOLD

You can use these as a starting point to do your own tweak-

called subsonic filter) to protect the speakers from harmful ultra-low frequencies.

Each preset stores all the values for each of the following amplifier controls:

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-1 MEM-2 MEM-3 MEM-4

memory key until the VFD display flashes STORED . Then release the memory key. The indicator which matches the preset you used will illuminate.

RECALLING A PRESET

M1 M2 M3 M4

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

stored

MEM-1 MEM-2 MEM-3MEM-4

ing or for quick push-a-button-and-be-done setup.

Any preset you store will replace the ones that come from the factory. You can reset all four preset back to factory defaults anytime simply by doing a reset in the RESET AMP menu.

Memory-2sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies and a 6 dB bass boost at 40 Hz.

*.) GAIN	INDICATORS		PRESETS
*.) EQ
*.) LO-PASS
*.) HI-PASS	M1	M2 M3	M4
*.) PHASE
*.) MUTE
*.) KOMPRESSOR	ESC	HOME	ENT

This gives you the ability to dial in four

completely different amplifier settings and store them in pre- sets for instant recall later.

It’s like a preset for your favorite radio stations...only better!

To recall a memory preset simply press and release the key. The matching indicator will light up and the amplifier will change all the corresponding controls to the values assigned to the memory pre- set.

PRESS &

RELEASE

M1 M2 M3 M4

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-1 MEM-2MEM-3 MEM-4

Here are the settings in each preset from the factory.

	MEMORY-1	MEMORY-2	MEMORY-3	MEMORY-4
GAIN LEVEL	6 DB	6 DB	6 DB	6 DB
EQ FREQUENCY	40 HZ	40 HZ	40 HZ	40 HZ
EQ BOOST/CUT	FLAT	+ 6 DB	+ 6 DB	+ 6 DB
EQ BANDWIDTH	3	3	3	3
LO-PASS SLOPE	24 dB	24 DB	24 DB	24 DB
LO-PASS FREQ	80 HZ	80 HZ	80 HZ	80 HZ
HI-PASS SLOPE	24 DB	24 DB	24 DB	24 DB
HI-PASS FREQ	25 HZ	25 HZ	25 HZ	25 HZ
PHASE L&R CH.	0 DEGREE	0 DEGREE	O DEGREE	O DEGREE
MUTE L&R CH.	OFF	OFF	OFF	OFF
KOMPRESSOR	OFF	OFF	CONTOUR	RED-LINE
KOMP ADJ.	0 DB	0 DB	0 DB	0 DB

Memory-3sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies, a 6 dB bass boost at 40 Hz and sets the Kompressor into CONTOUR mode.

Memory-4sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies, a 6 dB bass boost at 40 Hz and sets the Kompressor into RED-LINE mode.

As stated before you can always start with one of these presets, tweak it to fit your installation and then save your settings into a new preset.

30 SX .1 Series Amplifiers SX .1 Series Amplifiers 31