End Panel Views, Mounting, Installation | Kicker SX1250.1, SX650.1

End Panel Views

Features	The BLAST Port is used to connect the Remote Bass Level

	Controller and for transferring control signals from one SX
	amplifier to another SX amplifier. An RJ45 cable is required to
	connect the BLAST Port (Out) of one amp to the BLAST Port
	(In) of another. This is only required if you want to control
	more than one amplifier with the same Bass Level Controller.
	More details on this further in the manual.
	The speaker terminals are custom-machined connectors
	with full protective shrouds and are designed to accept heavy
	gauge speaker wire assures maximum power transfer and
	damping with minimal power loss.
	Gold-plated RCA input connectors and PAST jacks provide
	solid input and output connections for your pre-amp signal.
	BLAST Port In	BLAST Port Out

Speaker +	Left PAST
Speaker -	Right PAST
	Right Input
	Left Input

Custom-machined power block accepts up to a 2 Ga wire for both power and ground connections and up to an 8 Ga for remote turn-on assures maximum power transfer with minimal loss.

On-board fusing (number of fuses vary by amp size) to protect amplifier against over current conditions and reverse polarity.

Power LED indicates amplifier is powered up and operating.

Check Fuse LED indicates a fault with the end panel fuses. This could be fuses which are not seated properly, faulty fuses or blown fuses.

NOTE...

SX1250.1 does not have on-board fusing or the Check Fuse LED due to larger external fusing requirements.

Power LED

Check Fuse LED

Fusing

Ground

Remote

+ 12 Volt

Mounting

When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the area that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc.

All amplifiers generate heat under normal operation. Be sure to choose a location that allows adequate ventilation for the amplifier. Also consider that the air temperature inside an automobile’s trunk can reach upwards of 140 degrees fahren- heit. An amplifier mounted in the trunk may require additional cooling such as extra fans moving air around the amplifier’s chassis or ventilating the trunk to exchange the hot air in the trunk for cooler air outside. If possible, mounting the amp in the passenger compartment will allow cooler operation.

Remember that the controls on top of the amp will need to be accessible for adjustment later. Keep this in mind as you choose your amplifier’s mounting location.

Now that you are ready to mount your amplifier, use the supplied 3mm allen wrench to remove the amplifier EndKaps. This will give you access to the mounting holes in the amplifi- er and all wiring connections.

See Fig. 1

Remove					Remove
	AMP1			AMP2	Installation
	LOCK LEFT SYS RIGHT MUTE
	GAIN EQ LPF HPF PHASE KOMP
	*	kicker *
	MEM-1	MEM-2 MEM-3 MEM-4
	M1	M2	M3	M4
	ESC	HOME		ENT
Remove	Fig. 1				Remove

With the EndKaps removed, you now have access to the four mounting holes in the mounting feet and all wiring connections. Drill 4 holes using a 7/64” drill bit and use the supplied #8 screws to mount the amplifier.

See Fig. 2

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-1 MEM-2 MEM-3 MEM-4

M1 M2 M3 M4

ESC HOME ENT

6	SX .1 Series Amplifiers

	Fig. 2
SX .1 Series Amplifiers	7

SX650.1, SX1250.1 specifications

Kicker is known for its dedication to delivering top-tier audio performance, and the Kicker SX1250.1 and SX650.1 amplifiers stand out in the realm of car audio. Packed with robust features and innovative technologies, these amplifiers cater to both novice and expert audio enthusiasts.

Starting with the Kicker SX1250.1, this powerhouse monoblock amplifier is specifically designed to deliver a staggering 1,250 watts RMS at 1 ohm. With the ability to push your subwoofers to their limits, it provides deep, impactful bass that enhances your music experience. The SX1250.1 features a variable low-pass crossover, allowing users to fine-tune the cutoff frequency to perfectly match their subwoofers. Additionally, it is equipped with a built-in subsonic filter, which helps to eliminate unwanted lower frequencies that can lead to distortion.

The SX1250.1 utilizes advanced technology such as the Kicker's exclusive FIT (Fail-Safe Integration Technology), ensuring maximum compatibility with a variety of vehicle audio systems. This technology also aids in minimizing voltage loss and maximizing sound quality, resulting in an impressive audio output. The amplifier's thermal and short-circuit protection circuitry guarantees reliable performance, preventing overheating and ensuring longevity.

On the other hand, the Kicker SX650.1 is another exemplary model that emphasizes versatility and efficiency. This mono amplifier delivers 650 watts RMS at 1 ohm, making it suitable for smaller systems where space and power consumption are of concern. The SX650.1 also includes a variable low-pass crossover and bass boost feature, allowing users to customize their audio settings to suit their listening preferences.

Like its larger counterpart, the SX650.1 is built with FIT technology, ensuring a secure connection to your vehicle's audio system. Its compact design makes it easy to install in tight spaces without compromising on performance. Kicker has also included an integrated heatsink design to enhance cooling efficiency, ensuring optimal performance even during prolonged use.

Both the SX1250.1 and SX650.1 amplifiers boast a stylish and sleek appearance, with a distinctive Kicker logo that complements any audio setup. Whether you are a bass enthusiast seeking high-performance output or a casual listener looking for quality sound, the Kicker SX amplifiers deliver exceptional audio experience that is hard to match, making them a wise investment for any car audio lover.

Kicker SX1250.1, SX650.1 manual End Panel Views, Mounting, Installation

Models: SX650.1 SX1250.1

End Panel Views

Mounting

Installation

SX650.1, SX1250.1 specifications