KitchenAid 2003757 Copies of the standard listed may be obtained from, To rough in water line

Electrical Requirements

Electrical Shock Hazard Electrical ground is required. Do Not ground to gas pipe.

30 Not change the power supply cord plug. If it does not fit the outlet, have a proper Dutlet installed by a qualified electrician.

Do Not have a fuse in the neutral or grounding circuit.

Do Not use an extension cord.

Check with a qualified electrician if you are not sure the appliance is properly grounded.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSVNFPA 70

-latest edition** or Canadian Electrical Code, C22.1-1982 and C22.2 No. 01982 (or latest edition)+, and all local codes and ordinances.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

3-prong groundin - typeI. wall receptac ?e p

pow;;;;ppIy’grounding prong

A 120-volt, 60-Hz, AC-only, 1.5 or 20- ampere, fused, electrical supply is required. A time-delay fuse or circuit

breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong,

grounding-type wall receptacle, grounded in accordance with the National Electrical Code, ANSVNFPA 70 - latest edition** or Canadian Electrical Code, C22.1-1982 and C22.2 No. 01982 (or latest edition)+, and all local codes and ordinances.

Copies of the standard listed may be obtained from:

*Canadian Standard Association

178 Rexdale Boulevard

Etobicoke, Ontario M9W lR3

l * National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

Water Supply Requirements

Electrical Shock Hazard

Some water may remain in line. Electric drill must be grounded to prevent severe or lethal shock if water is in line and enters drill during use.

Failure to follow this

instruction can result in death or electrical shock.

To prevent property or product damage:

l Use only l/4” (6 mm) copper tubing for water line.

l Do Not install copper tubing in area where temperatures drop below 32°F (OOC).

l Before attaching copper tubing to refrigerator, flush at least 2 quarts (1.9 L) of water through the copper tubing and into a bucket to get rid of any particles in the water line.

l Do Not over-tighten clamp or sleeve. This will crush copper tubing.

. Check for leaks around saddle

Water line to refrigerator must provide

15-l 00 psi (103-690 kPa) water pressure.

To calculate length of l/4” (6 mm) O.D. copper tubing needed:

1.Locate a vertical l/2” (1.2 cm) to l-l /4” (3.2 cm) COLD water line near refrigerator area. A horizontal COLD water line can be used if directions in Step 4 are carefully followed.

2.Measure distance from cold water line to refrigerator area. Add 24” (61 cm) to this measurement.

To rough in water line:

3.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

4.Vertical cold water line: Use

grounded electric drill or hand drill to drill 3/l 6” (4.5 mm) hole in an easily accessible location in water line.

Horizontal cold water line: Use grounded electric drill or hand drill to drill 3/l 6” (4.5 mm) hole in the top of the water line. This will keep sediment from collecting in valve.

5.Position washer over hole in water line. Turn saddle valve handle clockwise to expose piercing lance a

maximum of 3/l 6” (4.5 mm). Align piercing lance over hole in water line. Place both halves of saddle valve bracket against water line. Turn saddle valve handle clockwise until

piercing lance enters hole in water line and is firmly seated. The

saddle valve is not in th position. Tighten packing nut.

Evenly and firmly tighten bracket screws so washer will make a water-tight connection. Do Not over-tighten screws; copper tubing could be crushed.

6.Check that both ends of copper tubing are cut square. Slide compression nut and sleeve onto copper tubing. Insert end of copper tubing completely into valve outlet. Tighten compression nut to outlet with adjustable wrench. Do Not overtighten.

7.Turn on main water supply. Check for leaks. Turn saddle valve handle

counterclockwise and run water through copper tubinq and into a bucket. Turn

saddle		-	nut	copper tubing
valve		compression
handle
clockwise
to	shut		I
off	water			union
		sleeve
to	copper	tubing.

8.Route copper tubing to refrigerator area.

9.Slide compression nut and sleeve over the water line. Connect union to compression nut and sleeve and

tighten. Do Not over-tighten. Page 7