KitchenAid 9759536B Installation Requirements, Tools and Parts, Location Requirements

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■	Tape measure	■	¹⁵⁄₁₆" combination wrench
■	Flat-blade screwdriver	■	Marker or pencil
■	Phillips screwdriver	■	Masking tape
■	Level	■	Pipe-joint compound
■ Hand or electric drill			resistant to LP gas
		■ Noncorrosive leak-detection
■	Wrench or pliers
			solution
	Pipe wrench
■		■	Stud finder

Parts needed

■A UL listed or CSA approved conduit connector

■UL listed wire connectors

Parts supplied

Check that all parts are included.

■Anti-tip bracket kit

	1"	1¾"
		(4.4 cm)
	(2.5 cm)
A		B

C

A. Anti-tip bracket - 1" (2.5 cm)

B. Anti-tip bracket - 1³⁄₄" (4.4 cm)

C. #10 x 2" Phillips head mounting screws (2)

NOTE: Anti-tip brackets must be securely attached to wall stud. Thickness of finished wall may require longer mounting screws to anchor bracket to wall. Longer mounting screws are available from your local hardware store. See “Install Anti-Tip Bracket” section.

■Backguard and attachment screws (7).

NOTE: The backguard included with the range is required if installed with less than 1" (2.5 cm) clearance from a combustible rear wall.

■Island trim and attachment screws (3).

NOTE: The island trim included with the range may be used if installed with 1" (2.5 cm) clearance from a combustible rear wall or with 0" (0 cm) clearance from a noncombustible rear wall.

■LP conversion kit.

NOTE: The cooktop is manufactured for use with Natural gas. To convert to LP gas, see the gas conversion instructions provided in the package containing literature.

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

All electrical connections should be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the right vertical surface of the oven door frame.

■It is recommended that a 600 CFM range hood be installed above the range.

■Recessed installations must provide complete enclosure of the sides and rear of the range.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■All openings in the wall or floor where range is to be installed must be sealed.

■Do not seal the range to the side cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The wall anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section.

■Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C). Use an insulated pad or ¼" (0.64 cm) plywood over carpet and under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

4