Manuals / KitchenAid / Kitchen Appliance / Coffeemaker

KitchenAid KPCG100 manual Care And Cleaning, Burr-Shaft Assembly Faceplate Assembly

Models: KPCG100

1 38

Page 27

CARE AND CLEANING

3.Carefully slide the faceplate assembly away from the motor housing. A separate burr-shaft assembly on the inside of the motor housing will usually slide out with the face plate assembly. Place a hand under the burr-shaft assembly to prevent it from falling as the faceplate assembly is removed. If the burr-shaft assembly does not slide out with the face-plate assembly, grasp the center shaft of the burr-shaft assembly and remove it from the housing.

Burr-Shaft Assembly

Faceplate Assembly

4.Using the burr-cleaning brush, clean the burr mounted on the burr-shaft assembly and the burr mounted within the motor housing.

NOTE: Never wash the burrs or burr- shaft assembly in water. Keep them dry at all times.

Page 27

Image 27

KitchenAid KPCG100 manual Care And Cleaning, Burr-Shaft Assembly Faceplate Assembly

Contents

RESULTS P R O L I N E S E R I E SPROFESSIONAL GUIDE TOSection Contents KPCG100MODEL BURR COFFEE MILLPage INTRODUCTION TABLE OF CONTENTSFEATURES AND OPERATION CARE AND CLEANINGWarranty for Puerto Rico WARRANTY AND SERVICE INFORMATIONTABLE OF CONTENTS Arranging for Service After the Warranty ExpiresPROOF OF PURCHASE PRODUCT REGISTRATIONSerial Number Date Purchased Store Name the word “DANGER” or “WARNING.” These words mean COFFEE MILL SAFETYYour safety and the safety of others are very important and othersSAVE THESE INSTRUCTIONS IMPORTANT SAFEGUARDSVolts 120 V.A.C. only Hertz 60 Hz NOTE This ELECTRICAL REQUIREMENTSFEATURESEST AND OPERATIONPETI FEATURESOPERATION Features and Operation Section ContentsBURR COFFEE MILL FEATURES MODEL KPCG100Model KPCG100 Burr Coffee Mill Coffee Bin Motor HousingOn/Off Switch Bean HopperPrecision Stainless Steel Cutting Burrs Faceplate Assembly ScrewsPower Cord with Tie Burr Cleaning BrushOperating the Coffee Mill USING THE PRO LINE SERIESBURR COFFEE MILL Before First UseBURR COFFEE MILL Electrical Shock Hazard Plug into a grounded 3 prong outletDo not remove ground prong Do not use an adapter USING THE PRO LINE SERIESFEATURES AND OPERATION 7. To grind coffee, flip the On/Off Switch to the “On” positionSetting ADJUSTING THE CUTTING BURRSGrind Setting Table Adjusting the Cutting BurrsContinued… The white grind control gearADJUSTING THE CUTTING BURRS Adjusting to Provide Coarser GrindsBURR COFFEE MILL TIPS PRO LINE SERIESContinued… Clean the coffee bin and cutting burrs frequently BURR COFFEE MILL TIPSPRO LINE SERIES Continued… HOW THE GRIND AFFECTS FLAVORPage Section Contents CLEANINGCARE Care and CleaningCleaning the Motor Housing and Hoppers CARE AND CLEANINGContinued… Cleaning the Cutting BurrsBurr-Shaft Assembly Faceplate Assembly CARE AND CLEANINGContinued… 5. After cleaning, tilt the grinder backward so the front of the motor housing faces upwardCARE AND CLEANING Adjusting The Cutting Burrs For WearTo replace the burrs Replacing the Cutting BurrsIf the mill is operating normally, but stops abruptly TROUBLESHOOTINGIf the mill does not run when switched on If the mill runs when switched on, but coffee does not grindSection Contents WARRANTY AND SERVICEINFORMATION Warranty InformationAND DISTRICT OF COLUMBIA COFFEE MILL WARRANTYLength of Warranty FOR THE 50 UNITED STATESCOFFEE MILL WARRANTY FOR PUERTO RICOARRANGING FOR HASSLE-FREE REPLACEMENTREPLACEMENT PARTS ORDERING ACCESSORIES ANDAND PUERTO RICO ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRESARRANGING FOR SERVICE OUTSIDE THE 50 UNITED STATESPage Specifications subject to change without notice FOR THE WAY IT’S MADEdZw703