Manuals / KitchenAid / Kitchen Appliance / Coffeemaker

KitchenAid KPCG100 manual Adjusting The Cutting Burrs For Wear, Care And Cleaning

Models: KPCG100

1 38

Page 29

CARE AND CLEANING

8.Place the faceplate assembly onto the motor housing. Make sure the numbers on grind level ring are positioned across the top of the assembly. Using your fingers, tighten the faceplate screws by turning them clockwise. Alternate tightening the screws, keeping them even – do not completely tighten one screw before tightening the other.

9.After the faceplate screws have been finger-tightened, use a flat- head screwdriver to tighten them until snug.

10.Place the grinder upright. It is now ready for use.

Adjusting The Cutting Burrs For Wear

The cutting burrs are made of high- quality stainless steel for exceptional longevity. After prolonged use, however, the burrs might require adjustment to compensate for wear. If your grinds – especially espresso – are not as fine as they used to be, an adjustment probably needs to be made.

Please see “Adjusting the Cutting Burrs” on page 16 for information on adjusting the burrs to provide maximum grind fineness.

Page 29

Image 29

KitchenAid KPCG100 manual Adjusting The Cutting Burrs For Wear, Care And Cleaning

Contents

PROFESSIONAL P R O L I N E S E R I E SGUIDE TO RESULTSMODEL KPCG100BURR COFFEE MILL Section ContentsPage FEATURES AND OPERATION TABLE OF CONTENTSCARE AND CLEANING INTRODUCTIONTABLE OF CONTENTS WARRANTY AND SERVICE INFORMATIONArranging for Service After the Warranty Expires Warranty for Puerto RicoSerial Number Date Purchased Store Name PROOF OF PURCHASEPRODUCT REGISTRATION Your safety and the safety of others are very important COFFEE MILL SAFETYand others the word “DANGER” or “WARNING.” These words meanSAVE THESE INSTRUCTIONS IMPORTANT SAFEGUARDSVolts 120 V.A.C. only Hertz 60 Hz NOTE This ELECTRICAL REQUIREMENTSOPERATION FEATURESFeatures and Operation Section Contents FEATURESEST AND OPERATIONPETIModel KPCG100 Burr Coffee Mill BURR COFFEE MILL FEATURESMODEL KPCG100 On/Off Switch Motor HousingBean Hopper Coffee BinPower Cord with Tie Faceplate Assembly ScrewsBurr Cleaning Brush Precision Stainless Steel Cutting BurrsBURR COFFEE MILL USING THE PRO LINE SERIESBefore First Use Operating the Coffee MillDo not remove ground prong Do not use an adapter Electrical Shock Hazard Plug into a grounded 3 prong outletUSING THE PRO LINE SERIES BURR COFFEE MILLFEATURES AND OPERATION 7. To grind coffee, flip the On/Off Switch to the “On” positionGrind Setting Table ADJUSTING THE CUTTING BURRSAdjusting the Cutting Burrs SettingContinued… The white grind control gearADJUSTING THE CUTTING BURRS Adjusting to Provide Coarser GrindsContinued… BURR COFFEE MILL TIPSPRO LINE SERIES PRO LINE SERIES Clean the coffee bin and cutting burrs frequentlyBURR COFFEE MILL TIPS Continued… HOW THE GRIND AFFECTS FLAVORPage CARE CLEANINGCare and Cleaning Section ContentsCleaning the Motor Housing and Hoppers CARE AND CLEANINGContinued… Cleaning the Cutting BurrsBurr-Shaft Assembly Faceplate Assembly CARE AND CLEANINGContinued… 5. After cleaning, tilt the grinder backward so the front of the motor housing faces upwardCARE AND CLEANING Adjusting The Cutting Burrs For WearTo replace the burrs Replacing the Cutting BurrsIf the mill does not run when switched on TROUBLESHOOTINGIf the mill runs when switched on, but coffee does not grind If the mill is operating normally, but stops abruptlyINFORMATION WARRANTY AND SERVICEWarranty Information Section ContentsLength of Warranty COFFEE MILL WARRANTYFOR THE 50 UNITED STATES AND DISTRICT OF COLUMBIACOFFEE MILL WARRANTY FOR PUERTO RICOREPLACEMENT PARTS HASSLE-FREE REPLACEMENTORDERING ACCESSORIES AND ARRANGING FORARRANGING FOR SERVICE OUTSIDE ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRESTHE 50 UNITED STATES AND PUERTO RICOPage dZw703 Specifications subject to change without noticeFOR THE WAY IT’S MADE