Toshiba 37X3000A, 46X3000A Adjusting the basic picture quality, Activating the black stretch

Using the TV’s features (General)

Adjusting the basic picture quality

1In Digital TV, press M, then press ￿ or ￿ to display the TV set up then press Q.

2Press ￿ or ￿ to display the PICTURE menu.

3In Analog TV, press M and ￿ or ￿ to display the

PICTURE menu.

PICTURE
Picture settings	OK
3D Color management	Off
Base color adjustment
Active Backlight Control	On
Cinema mode	On
MENU Back EXIT Watch TV

4Press ￿ or ￿ to select the Picture settings menu, then press Q.

Picture settings	1/2
Bac k light	100
Contrast	100
Brightness	50
Color	50
Tint	0
Sharpness	0

MENU Back EXIT Watch TV

5Press ￿ or ￿ to select an item you want to adjust, then press ￿ or ￿ to adjust the settings as required.

Contrast 100

Selection	￿	Pressing	￿
Back light	darker		brighter
Contrast	lower		higher
Brightness	darker		brighter
Color	paler		deeper
Tint	reddish		greenish
Sharpness	softer		sharper
Notes:

•The Tint may only be adjusted on NTSC signal.

•In the PC input mode (- page 25), Color, Tint and Sharpness modes are not available.

Activating the black stretch

This function increases the strength of dark areas of the picture which improves definition.

1From the Picture settings menu, press ￿ or ￿ to select Black stretch on the 2nd page.

Picture settings	2/2
Black stretc h	On
MPEG NR	Low
DNR	Auto
Color Temperature	Cool
MENU Back EXIT Watch TV

2Press ￿ or ￿ to select On or Off.

Black stretch On

Note:

In the PC input mode (- page 25), this mode is not available.

Activating the MPEG NR (Noise Reduction)

If the receiving signal of MPEG is a mosquito (grained) noise depending on the compression and conversion, the noise may be reduced when using this function.

1From the Picture settings menu, press ￿ or ￿ to select MPEG NR on the 2nd page.

2Press ￿ or ￿ to select Off, Low, Middle or High.

MPEG NR High

Note:

In the PC input mode (- page 25), this mode is not available.

Activating the DNR (Digital Noise

Reduction) - analog only -

If the receiving signal is weak and the picture is blurry, the picture may be improved when using this function.

1From the Picture settings menu, press ￿ or ￿ to select DNR on the 2nd page.

2Press ￿ or ￿ to select Auto, Off, Low, Middle or High.

DNR Auto

Selecting the color temperature

You can change the tone of the picture by selecting from three preset color temperatures: Cool, Normal or Warm.

1From the Picture settings menu, press ￿ or ￿ to select Color Temperature on the 2nd page.

2Press ￿ or ￿ to select mode you prefer.

Color Temperature Cool

Cool: Lends a blue hue to the picture.

Normal: Neutral

Warm: Lends a red hue to the picture.

Adjusting the color management

You can adjust the picture color quality by selecting from 6 base color adjustments : Red, Green, Blue, Yellow, Magenta or Cyan.

1Press M, then press ￿ or ￿ to display the PICTURE menu.

2Press ￿ or ￿ to select 3D Color management, then press ￿ or ￿ to select On.

3D Color management On

3Press ￿ or ￿ to select Base color adjustment.

4Press Q, then press ￿ or ￿ to select an item you want to adjust.

Base color adjustment

		Hue	Saturation	Brightness
	Red	0	0	0
	Green	0	0	0
	Blue	0	0	0
	Yellow	0	0	0
	Magenta	0	0	0
	Cyan	0	0	0
Reset				OK
MENU Back		EXIT Watch TV

20