Manuals / KitchenAid / Kitchen Appliance / Range

KitchenAid W10526089A Location Requirements, Mobile Home Additional Installation Requirements

Models: W10526089A

1 44
Download 44 pages 19.96 Kb
Page 5
Image 5

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the oven door on the right-hand side oven door trim.

■The range should be located for convenient use in the kitchen.

■Recessed installations must provide complete enclosure of the sides and rear of the range.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood or microwave hood combination that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■All openings in the wall or floor where range is to be installed must be sealed.

■Do not seal the range to the side cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section.

■Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).

■Use an insulated pad or ¼" (0.64 cm) plywood under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

5

Page 4 Page 6
Page 5
Image 5
KitchenAid W10526089A installation instructions Location Requirements, Mobile Home Additional Installation Requirements
Page 4 Page 6

W10526089A specifications

The KitchenAid W10526089A is a highly efficient and versatile appliance that serves as a replacement water filter, designed specifically for select KitchenAid refrigerators. This model ensures that you and your family can enjoy clean, fresh-tasting water and ice. One of its main features is the ability to reduce contaminants commonly found in tap water, including chlorine, lead, and sediment, ensuring a healthier drinking experience.

One of the standout technologies in the W10526089A is its advanced filtration system, which includes activated carbon. This technology works effectively to absorb impurities that can affect the taste and purity of water. Not only does it enhance flavor, but it also helps in removing odors, delivering crisp and refreshing hydration. The filter is designed to provide up to six months of use, depending on water quality and consumption, which ensures that you get great performance without frequent replacements.

Installation of the W10526089A is straightforward, making it easy for homeowners to replace their existing filter without needing professional assistance. It features a simple twist-and-lock design that allows for quick and hassle-free changes. This ease of use is a significant benefit, particularly for busy families who rely on continual access to filtered water.

In terms of characteristics, the W10526089A is designed to fit within specific KitchenAid refrigerator models, ensuring seamless compatibility. Its compact size allows it to fit discreetly behind the refrigerator’s interior, maintaining aesthetic appeal while ensuring functionality. Additionally, the filter carries the NSF International certification, which verifies that it meets strict public health standards for water filtration safety and performance.

The W10526089A also comes with a clear indicator that alerts users when it’s time to replace the filter, promoting better maintenance and ensuring your water remains pure at all times. This intelligent feature minimizes the guesswork involved with water filter replacement, leading to improved health and convenience.

Overall, the KitchenAid W10526089A water filter is a reliable investment for anyone looking to improve their home’s drinking water quality, offering advanced filtration technologies, user-friendly design, and a commitment to safety and performance.