Table of Contents

Section 2: Operating Instructions

Land Pride

How the Seeder Works

The following is a brief description of how your Overseeder works.

The power to drive the seed cups comes from the gauge wheels or rear roller turning against the ground while traveling. Power is then transmitted through roller chains to the seed cups. Seed is metered out of the cups at a rate proportional to the distance driven. This ensures that the rate applied in pounds per 1000 square feet or pounds per acre remains constant as ground speed is varied.

Cup metering speed can be adjusted to either a high or low range by changing the speed change sprocket. Also, the rate seed falls through the seed cups is adjustable using the seed rate adjustment lever located at the back of the seeder.

Metered seed is broadcast onto the ground surface and into the slits made by the rotor knives. Seeds drops in front of the rear roller to allow the roller to firm the soil around the seeds.

General Notes for Field Operations

Before proceeding with the first time set-up or before making any adjustments mentioned in this section, make every effort to obtain and hitch a tractor to the Overseeder.

1.This Overseeder can be transported with a full box of seeds. It is best not to do this unless necessary because the increased weight does increase the chances for problems on the road.

2.Do not exceed 20 miles per hour when transporting.

3.Calibrate your seeder sprocket speed and seed cup rate adjustment lever based on type of seed you are using. Calibration information is located on the inside of your box lid or on page 18.

4.Refer to Figure 3-1 on page 18. Make sure the feed cup door adjustment handle on each cup is set the same across the Overseeder. Usually in the highest position.

5.Never allow anyone to ride on the Overseeder.

6.Maximum seeding speed will vary according to soil conditions.

Parking

The following steps should be done when preparing to store the Overseeder or unhitching it from the tractor. See also Storage under the “Maintenance and Lubrication” section on Page 31 for additional information on long term storage of your Overseeder.

1.Park the Overseeder on a level, solid area.

2.Shut off tractor engine and engage parking brake.

3.Refer to Figure 2-2. Place rear roller stop pin (#1) and hairpin cotter (#2) in parking position.

4.Unhitch from tractor.

14669

Rear Roller Stop Pin in Parking Position

Figure 2-2

7.Check oil level in gearbox and chaincase.

8.Check that all plugs and caps have been replaced properly.

9.Be sure all Overseeder knives, bolts and nuts are tight.

10.Be certain all guards and shields are in place and secure.

11.Grease PTO shaft and all other grease fittings.

12.Clear the area to be over-seeded of rocks, branches and other foreign objects.

13.Tall grass and weeds should be mowed before overseeding.

14.Operate with 540 rpm PTO tractor.

15.At first begin overseeding at a slow forward speed and shift up until the desired speed is achieved.

16.Overseeder knives will cut better at a faster rotor speed than at reduced throttle.

17.Do not engage PTO at full throttle.

18.Never back up with Overseeder in the ground.

19.Overseeding should not be done in wet conditions as soil will stick to the knives.

20.After overseeding the first 50 feet, stop and check to see that the Overseeder is adjusted properly.

21.Do not make sharp turns or attempt to back up while Overseeder is in the ground.

22.Do not engage PTO with machine in the fully raised or fully lowered position.

16 OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M

2-16/09

Page 18
Image 18
Land Pride OS1548, OS1572 manual How the Seeder Works, General Notes for Field Operations, Parking

OS1572, OS1548 specifications

The Land Pride OS1548 and OS1572 are outstanding implements designed to enhance the efficiency and productivity of landscape and turf maintenance. These models are part of Land Pride's lineup of high-quality equipment, built for durability and performance.

One of the main features of the OS1548 and OS1572 is their robust construction. Each model is meticulously crafted using high-strength steel, which gives them a solid framework that can withstand rigorous daily use. This durability is complemented by high-quality welds and a corrosion-resistant finish, ensuring that these implements will serve users well over the years, even in challenging environments.

Both models are equipped with a high-capacity hopper that makes them suitable for all types of seed and fertilizer applications. The OS1548 has a 48-inch working width, while the OS1572 boasts a larger 72-inch width. This variety allows operators to choose a model that best fits their specific needs, whether for residential or commercial use. The ample hopper capacity allows for extended work periods without constant refilling, maximizing efficiency and minimizing downtime.

The OS1548 and OS1572 come with a unique broadcasting system that ensures even distribution of seeds and fertilizers across the treated area. This is crucial for achieving uniform growth and maximizing the effectiveness of inputs. The finely tuned spread pattern also reduces waste and ensures that materials are used economically.

Another innovative feature of these models is their user-friendly design. They come equipped with adjustable settings that allow operators to easily control the flow rate of the materials being spread. This feature is particularly beneficial for tasks that require precision, such as overseeding or applying specific fertilizers.

Both models are designed for versatility, capable of tackling various landscaping tasks. Whether you're preparing a new lawn, refreshing a garden bed, or maintaining a sports field, the OS1548 and OS1572 deliver exceptional results.

In conclusion, the Land Pride OS1548 and OS1572 are exceptional implements that combine strength, efficiency, and user-friendly features. With their robust construction, high capacity, and precise broadcasting system, they are ideal for anyone looking to enhance their landscaping capabilities. These models exemplify Land Pride's commitment to quality and innovation in turf management equipment.