Table of Contents

Section 1: Assembly & Set-up

Land Pride

Refer to Figure 1-9:

4.If rear roller (#13) is in the long arm position as shown. Attach front chain guard (#1) and rear chain guard (#2) with 5/16” x 2 1/2” bolts (#3) in the locations shown.

14662

Long Arm Chain Guard Location

Figure 1-9

Driveline Installation

The tiller driveline is coupled to the tractor shaft with either push pin couplers, pull collar couplers or a combination of both and on the implement end with a slip clutch and pull collar coupler for protection from shock loads.

Always engage PTO at low engine rpm to minimize driveline start-up torque. Drivelines with friction clutches must go through a “run-in” operation prior to initial use and after long periods of inactivity. See “Section 4: Maintenance & Lubrication” on page 31 for a detailed description of maintaining the driveline.

If the Overseeder is to be used on more than one tractor, an additional PTO shaft may be required - especially if a quick hitch is used.

24872

Maximum PTO driveline Movement During Operation

Figure 1-10

IMPORTANT: Always check driveline maximum and minimum length during initial set-up, when connecting to a different tractor and when alternating between using a quick hitch and a standard 3-point hitch. More than one driveline may be required to fit all applications.

IMPORTANT: It is necessary to aligning the tractor’s PTO shaft level with Overseeder’s PTO shaft when checking to see if the driveline’s minimum length is correct. Too long a driveline can damage the tractor, gearbox and driveline.

Check Driveline Minimum Length

Refer to Figure 1-11:

1.Start tractor and slowly engage tractor’s hydraulic 3-point lift to raise the lower arms until the Overseeder’s driveline shaft is approximately level with tractor's PTO shaft.

2.Slide slip clutch end of driveline over the splined input shaft of gearbox. Secure with driveline yoke locking device.

!CAUTION

Tractor PTO shields and guards must be in place at all times during operation!

!CAUTION

Do not use a PTO adaptor with a quick hitch. A PTO adapter will increase the strain on the tractor’s PTO shaft and can damage the PTO shaft and mower driveline.

IMPORTANT: Some tractors are equipped with multi-speed PTO ranges. Be certain your tractor ‘s PTO is set for 540 rpm.

IMPORTANT: Avoid premature driveline breakdown. A driveline that is operating must not exceed an angle of 25 degrees up or down while operating the 3-point lift. See Figure 1-10.

IMPORTANT: For easier access to gearbox input shaft, remove driveline guard at the gearbox.

3.Slide opposite end of driveline yoke over the tractor’s splined PTO shaft. Secure with driveline yoke locking device. Skip to step 4 if driveline fits between tractor and implement.

11150

Driveline Quick Disconnect

Figure 1-11

12 OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M

2-16/09

Page 13 Page 15
Page 14
Image 14
Land Pride OS1548, OS1572 manual Driveline Installation, Check Driveline Minimum Length, Long Arm Chain Guard Location
Page 13 Page 15

OS1572, OS1548 specifications

The Land Pride OS1548 and OS1572 are outstanding implements designed to enhance the efficiency and productivity of landscape and turf maintenance. These models are part of Land Pride's lineup of high-quality equipment, built for durability and performance.

One of the main features of the OS1548 and OS1572 is their robust construction. Each model is meticulously crafted using high-strength steel, which gives them a solid framework that can withstand rigorous daily use. This durability is complemented by high-quality welds and a corrosion-resistant finish, ensuring that these implements will serve users well over the years, even in challenging environments.

Both models are equipped with a high-capacity hopper that makes them suitable for all types of seed and fertilizer applications. The OS1548 has a 48-inch working width, while the OS1572 boasts a larger 72-inch width. This variety allows operators to choose a model that best fits their specific needs, whether for residential or commercial use. The ample hopper capacity allows for extended work periods without constant refilling, maximizing efficiency and minimizing downtime.

The OS1548 and OS1572 come with a unique broadcasting system that ensures even distribution of seeds and fertilizers across the treated area. This is crucial for achieving uniform growth and maximizing the effectiveness of inputs. The finely tuned spread pattern also reduces waste and ensures that materials are used economically.

Another innovative feature of these models is their user-friendly design. They come equipped with adjustable settings that allow operators to easily control the flow rate of the materials being spread. This feature is particularly beneficial for tasks that require precision, such as overseeding or applying specific fertilizers.

Both models are designed for versatility, capable of tackling various landscaping tasks. Whether you're preparing a new lawn, refreshing a garden bed, or maintaining a sports field, the OS1548 and OS1572 deliver exceptional results.

In conclusion, the Land Pride OS1548 and OS1572 are exceptional implements that combine strength, efficiency, and user-friendly features. With their robust construction, high capacity, and precise broadcasting system, they are ideal for anyone looking to enhance their landscaping capabilities. These models exemplify Land Pride's commitment to quality and innovation in turf management equipment.
Top Page Image Contents