Table of Contents

Section 2: Assembly & Set-up

Land Pride

Dealer Preparations

This cutter has been assembled at the factory. Some preparation will be necessary to attach the cutter to the customer’s tractor. Ensure that the intended tractor conforms to the requirements stated under the heading “Tractor Requirements” on page 9.

IMPORTANT: Hydraulic fluid must be added to the hydraulic reservoir before this unit is placed into operation. Do not attempt to run the pump without fluid or damage to the pump will occur.

3-Point Hookup

Prepare the cutter as follows:

1.Locate the cutter on a flat and level concrete surface.

2.For proper hitch configuration determine the hitch category for the tractor being used.

(Refer to Figure 2-2on page 11)

3.Back the tractor into position and connect the

3-Point hitch arms and top link. Start the tractor, then slowly raise the 3-Point hitch about 1-2". Stow the jack stands in the raised position.

Check to be sure that the deck safety chain is in place.

Slowly operate the tractor's 3-Point hydraulic control up and down and check for clearance between the tires, reservoir, frame, drawbar etc.

Ensure that the lower arms are blocked to prevent excessive side movement. Adjust the tractor's Lower lift arms to level the cutter from left to right. Adjust the top-link so that the cutter is approximately level from front to rear. A final adjustment will be made later.

Preparation Checklist

Before operating this unit, 80-90 EP Gear Lube must be added to the gearbox & motor as indicated in the maintenance lubrication section (page 27) of this manual.

35 Gallons of Hydraulic Fluid for the hydraulic reservoir. Use any high quality mineral based hydraulic fluid such as Mobil Fluid 424 with a viscosity rating of 10W-30.

Additional hydraulic fluid (approx 2 gallons) for the tractor reservoir.

Miscellaneous assembly tools: hammer, tape measure, hacksaw, assortment of wrenches and sockets,1/4" drill/drill bits,

spirit level.

Quick disconnect adaptors to match your tractors duplex outlets. Quantities required depend on options selected:

(2)If equipped with Electric Cylinder Control Option

(6)If not equipped with Electric Switching Option

(2)If equipped with hydraulic Breakaway Cylinder Option

Possible need for forklift or hoist capable of lifting 2500 lbs.

Auxiliary tractor weights (depending on tractor size).

A minimum of two people available during assembly.

If a pin, bolt or other part has been removed, and you are unsure where it is used, use the parts section of this manual to identify it. Be sure the part gets used in the correct location. By double checking while you assemble, you will lessen the chance of using a bolt incorrectly that may be needed later.

Safety decals are legible and undamaged from shipment.

PTO shaft and loose parts bag/box shipped with the cutter.

10 RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Page 11 Page 13
Page 12
Image 12
Land Pride RCP2560, RCPM2560, Parallel Arm Rotary Cutter manual Dealer Preparations, Point Hookup, Preparation Checklist
Page 11 Page 13

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.
Top Page Image Contents