Land Pride
Section 2 Operating
Tractor Requirements | SPS2048. |
This Pulverizer Seeder is designed for tractors in the Category 1 class. Horsepower rating of the tractor should not exceed 40 HP.
Adequate front end weight is required on tractors for use with the seeder. Check tractor’s
NOTE: In order to maintain steering control, ballast may have to be added to your tractor. To determine whether or not to add ballast, refer to your tractor operator’s manual.
Operating Check List
In addition to design and configuration of equipment; hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved in its operation, transport, maintenance and storage of equipment. Before beginning to operate your Seeder, the following inspection should be performed.
|
| Check | Reference |
|
| Read and follow the “Safety Rules” | Important Safety |
|
| ||
|
| carefully. | Information Page 1- |
|
| ||
|
|
| 6 |
|
|
|
|
|
| Read all of the "Tractor Hook Up" and | Section 2 |
|
| ||
|
| preparation instructions. | page 7 |
|
| ||
|
|
|
|
|
| “Basic Operations” in this Manual | Operator’s |
|
| ||
|
|
| Manual |
|
|
| |
|
|
|
|
|
| Lubricate the seeder as needed. Refer to | Section 4 |
|
| ||
|
| "Lubrication" | page 20 |
|
| ||
|
|
|
|
|
| Check the seeder initially and periodically for | Section 8 |
|
| ||
|
| loose bolts & pins, "Torque Values Chart". | page 26 |
|
| ||
|
|
|
|
|
| Make sure all guards and shields are in | Operator’s |
|
| ||
|
| place. | Manual |
|
| ||
|
|
|
|
|
| Check initially and periodically for loose bolts, | Operator’s |
|
| ||
|
| pins, and chains. | Manual |
|
| ||
|
|
|
|
|
| Inspect the feed cups and seed tubes for | Section 7 |
|
| ||
|
| foreign matter. | page 25 |
|
| ||
|
|
|
|
|
| Set speed change sprocket for drive type | Section 3 |
|
| ||
|
| desired. | page 9 |
|
| ||
|
|
|
|
|
| Set seed rate. See "Seed Rate Charts". | Section 3 |
|
| ||
|
|
| page 12 |
|
|
| |
|
|
|
|
Tractor 3-Point Hookup
1.Back tractor up to seeder until
2.Secure the tractor’s
3.Secure the tractor’s top link to the seeder top hitch using a 1” diameter hitch pin. Adjust tractor top link in order to level the seeder.
Seeder Preparation and Use
Before proceeding with the first time setup, or before making any adjustments mentioned in this section, make every effort to obtain and hitch a tractor to the seeder.
1.This seeder can be transported with a full box of seed. It is best not to do this unless necessary because the increased weight does increase the chances for problems on the road. Do not exceed 20 miles per hour.
2.Calibrate your seeder for a proper rate based on the seed you are using. Calibration information is located on the inside of your box lid or on page 9.
3.Make sure the feed cup door adjustment handle on each cup is set the same across the seeder.
4.Never allow anyone to ride on the seeder.
5.Maximum seeding speed will vary according to soil conditions.
6.Check that all plugs and caps have been replaced properly.
7.Be sure all bolts and nuts are tight.
8.Be certain all guards are in place and secure.
9.Clear the area to be seeded of rocks, branches and other foreign objects.
10.To begin seeding lower unit to the ground.
11.At first begin seeding at a slow forward speed and shift up until the desired speed is achieved.
12.Periodically check that seed is being distributed through the feeder cups.
Transporting
!CAUTION
When traveling on public roads whether at night or during the day, use accessory light and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws.
1.Select a safe ground travel speed when transporting from one area to another. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.
2.Reduce tractor ground speed when turning. Leave enough clearance so the seeder does not contact obstacles such as buildings, trees or fences.
3.When traveling over rough or hilly terrain, shift tractor
6/26/02 | SPS20 & SPS30 Series Pulverizer Seeders | 7 |
