Leviton ACS15-1L installation instructions Identifying your wiring application most

DI-000-ACS15-00A-X0

Single Pole (One location) or 3-Way (Multi-location)

Electronic Switch

Cat. No. ACS15-1L (Lighted)

Incandescent-1800W – Magnetic Low-Voltage-1800VA (1440W)

Electronic Low-Voltage-1800W – Fluorescent-1800VA – Supplemental-1/2 HP

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:

•To be installed and/or used in accordance with appropriate electrical codes and regulations.

•If you are unsure about any part of these instructions, consult a qualified electrician.

•Acenti™ electronic switches are not compatible with standard 3-way or 4-way switches. They must be used with compatible Acenti™ on/off remotes.

•Recommended minimum wall box depth is 2-1/2".

WARNINGS AND CAUTIONS:

•Use only one (1) electronic switch in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4 matching remotes with LEDs.

•Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.

•Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

•Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

Tools needed to install your Switch:

Slotted/Phillips Screwdriver	Electrical Tape	Pliers
Pencil	Cutters	Ruler

INSTALLING YOUR SWITCH

NOTE: Use check boxes √ when Steps are completed.

Step 1 WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

OFF ONOFF ON

OFF ONOFF ON

OFF ONOFF ON

OFF ONOFF ON

OFF	ON	OFF	ON
OFF	ON	OFF	ON

Step 2 Identifying your wiring application (most

*IMPORTANT: For 3-Way applications, note that one of the screw terminals from the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the switch wall box and remote wall box.

Step 3 Preparing and connecting wires:

This switch can be wired using side wire terminal screws or through backwire openings. Choose appropriate wire stripping specifications accordingly.

	Cut		Strip Gage (measure
		5/8"
(if necessary)
		(1.6 cm)	bare wire here)

Step 4 cont’d

•Leviton recommends to temporarily position the Alignment Plate prior to wiring the device. If the wall box wires extend at least 6 inches out of the wall box, it is also possible to install the Alignment Plate after the device has been wired (refer to Wallplate instruction sheet).

•The Alignment Plate must be installed with the tab towards the bottom.

•Leviton recommends the following 3 methods to temporarily hold the Alignment Plate – use of device mounting screw, use of wall box wires, or use of electrical tape (refer to the following figures):

A	Mounting
	Screw
	P
	TO
	Alignment
Alignment Plate Held	Plate
By Mounting Screw

Step 5a	Installing your Switch –
	Single-Pole Wiring Application:
			Terminal
			Screw marked
			White (WH)
	Terminal	BL	WH	1
				2
Screw marked
Black (BL)
	Terminal			3
		YL/RD RD		4
Screw marked
Yellow/Red			Terminal
	(YL/RD)
			Screw marked
			Red (RD)

Terminal Label:

Use Terminal for 3-Way or More Applications Only.

For Single-Pole Applications, Do Not Remove This

Label.

Switch

common):

NOTE: If the wiring in the wall box does not resemble any of these configurations, consult a qualified electrician.

Side Wire Connection	Back Wire (either hole may be used)
Side wire terminals accept	Back wire openings use #14-12 AWG
#14 AWG solid copper wire only.	solid copper wire only.

B

WH

Green

Ground

Screw

BL Hot (Black)

YL/RD

• Make sure that the ends of the wires from the wall box are

Black

RD

straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

TOP

Alignment Plate

Line 120VAC, 60Hz

Held By Wires

Load

Use Terminal for 3-Way or More Applications Only.

For Single-Pole Applications, Do Not Remove This Label.

Step 4 Installing your Alignment Plate:

White

	3
3	4
4	5

Single-Pole		3-Way
1.	Line (Hot)	1.	Line or Load (See important*
2.	Neutral	2.	instruction)
3.	Ground		Neutral
4.	Load	3.	Ground

4.First Traveler – note color

5.Second Traveler – note color NOTE: For matching remote w/LEDs installation, the First Traveler becomes Line Hot.

Important Notice for Installer

To achieve proper aesthetic installation of the Acenti products, the wall surface surrounding the wall box opening must be fairly flat and free of irregularities. The wall box must be level and recessed or flush to the wall surface. The Acenti installa- tion system allows for adjustments that will correct minor flaws that may be present in the installation area.

This device must be installed with the Acenti™ Alignment Plate. The Alignment Plate is packaged with the Acenti™ Wallplate, which is sold separately from this device.

The Alignment Plate will function properly only if it is mounted to a flat wall surface as described above.

Electrical

C Tape

TOP

Alignment Plate

Held By Tape

•For Single-Pole Application, go to Step 5a.

•For 3-Way Coordinating Remote (no LEDs) Application, go to Step 5b.

•For 3-Way Matching Remote (with LEDs) Application, go to Step 5c.

Neutral (White)

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

•Green or bare copper wire in wall box to Green terminal screw.

•Line Hot wall box wire to terminal screw marked "BL".

•Load wall box wire to terminal screw marked "RD".

•Line Neutral wall box wire to terminal screw marked “WH”.

•Switch terminal screw marked "YL/RD" should have Red insulation label affixed.

NOTE: If insulating label is not affixed to terminal screw marked "YL/RD", use electrical tape to cover.

•Proceed to Step 6.