APPENDIX
Data5: | 7 | Main/Sub | 6 | Two/One | 5 | Using Physical | 4 | 3 | 2 | 1 | 0 | Step |
|
| Part Channel |
| |||||||||
| Picture | Channel | Reserved |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 | Main | 0 | Two | 0 | Use | x | 0 | 0 | 0 | 0 | NTSC Air |
|
|
|
|
|
|
|
|
|
|
|
| |
| 1 | Sub | 1 | One | 1 | No Use | x | 0 | 0 | 0 | 1 | NTSC Cable |
|
|
|
|
|
|
| x | 0 | 0 | 1 | 0 | ATSC Air |
|
|
|
|
|
|
| x | 0 | 0 | 1 | 1 | ATSC Cable_std |
|
|
|
|
|
|
| x | 0 | 1 | 0 | 0 | ATSC Cable_hrc |
|
|
|
|
|
|
| x | 0 | 1 | 0 | 1 | ATSC Cable_irc |
|
|
|
|
|
|
| x | 0 | 1 | 1 | 0 | ATSC cable_auto |
|
|
|
|
|
|
| x | 0 | 1 | 1 | 1 | Reserved |
|
|
|
|
|
|
| x | x | x | x | x | ... |
|
|
|
|
|
|
| x | 1 | 1 | 1 | 1 | Reserved |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
APPENDIX
All data are transmitted by Hexadecimal code
*Two/One part Channel: 6th bit
This bit is used in a
*Using physical channel: 5th bit
If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using physical channel bit must be low(0).
But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable.
If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1).
Example)
1.Analog channel: NTSC cable, channel number(35),
main picture Command: ma 00 23 xx xx xx xx 01
attribute(0x01): main picture, two part(it’s not mandatory), using physical channel, NTSC cable ‘xx’ data: don’t care major and minor channel number in case analog channel tuning.
2.Digital channel: ATSC air, channel number(don’t know physical channel, major(30), minor(3)), sub picture Command: ma 00 xx 00 1E 00 03 A2 attribute(0xA2): sub picture, two part, not using physical channel, ATSC air ‘xx’ data: don’t care analog channel number in case digital channel tuning.
3.Digital channel: ATSC air, channel number(physi- cal(20),major(20), minor(3)), sub picture Command: ma 00 14 00 14 00 03 82
attribute(0x82): sub picture, two part, using physical channel, ATSC air
23.Channel Add/Del (Command: m b) To add and delete the channels
Transmission [m][b][ | ][Set ID][ | ][Data][Cr] | |
Data 0: Channel Delete | Data 1: Channel Add | ||
|
|
| |
Acknowledgement [b][ | ][Set ID][ | ][OK/NG][Data][x] | |
|
|
|
|
24.Key (Command: m c)
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]s Data Key code: Refer to page 90.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
25.Back light(Command: m g) To adjust screen back light.
Transmission [m][g][][Set ID][][Data][Cr]
Data Min:0 ~ Max:64(*transmit by Hexadecimal code) Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement[a][ ][Set ID][ ][OK][Data0][Data1] [Data2][Data3][Data4][x][a][ ][Set ID]
[ ][NG][Data0][x]
98
