LG Electronics HCS6600 setup guide Installing CodePlus Transcoder Cards

Installing CodePlus Transcoder Cards

Slots

3 & 4

CONTROLLER

Slot

Slot 1

Slot 2

HCS6600

Slot 5

Slot 6

Slot 7

Slot 8

Slot 9

Slot 10

Slot 11

Slot 12

HCS6600

HCS6600

HCS6600

HCS6300

HCS6600

HCS6600

HCS6600

HCS6600

HCS6600

HCS6600

SERVICE

ETHERNET

PORT

SERVICE

SERVICE

SERVICE

SERVICE

SERVICE

SERVICE

SERVICE

SERVICE

SERVICE

PORT

PORT

RESET

PORT

PORT

PORT

PORT

PORT

PORT

PORT

RESET

RESET

RESET

RESET

RESET

RESET

RESET

RESET

RESET

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

I

1

I

1

I

1

I

1

SERVICE

I

1

I

1

I

1

I

1

I

1

I

1

3

3

3

3

3

3

3

3

3

E

9

E

9

3

10

E

9

PORT

E

9

E

9

E

9

E

9

E

9

E

9

E

E

E

E

E

E

E

E

E

E

E

4

E

4

9

E

4

RESET

E

4

E

4

E

4

E

4

E

4

E

4

B

B

E

B

B

B

B

B

B

B

I

1

I

1

E

4

I

1

STATUS

I

1

I

1

I

1

I

1

I

1

I

1

E 3

E 3

B

E 3

E 3

E 3

E 3

E 3

E 3

E 3

E 9

E 9

E 9

E 9

E 9

E 9

E 9

E 9

E 9

E 4

E 4

I

1

E 4

RF OUT

E 4

E 4

E 4

E 4

E 4

E 4

A

A

A

A

A

A

A

A

A

E 3

E 9

E 4

ASI OUT

ASI OUT

A

ASI OUT

ASI OUT

ASI OUT

ASI OUT

ASI OUT

ASI OUT

ASI OUT

ASI OUT

CONTROLLER Slot

The card in this slot may vary depending on system features.

Note: All cards used in the card frame must be inserted and removed by

qualified service personnel only.

Note: Use extreme care when handling an HCS6600 card. Always observe proper

precautions with respect to static electric- ity and mechanical shock. When not installed in a card frame, return the HCS6600 card to the anti-static bag in which it was shipped.

Note: The CodePlus series products are NOT designed to be hot-swappable!!!

Power must be removed to the card frame before any CodePlus transcoder cards are inserted or removed.

Note: The card slots in the card frame are NOT all identical!!! An HCS6600 card can only be installed in Slots 1 to 6 and

7 to 12. The CONTROLLER slot between Slots

6 and 7 is dedicated for optional feature cards and is not compatible with HCS6600 cards.

Note: When installing cards, remove

blank cover plates and insert new cards as applicable. For ports that will not be

used, leave the blank cover plates in place for proper ventilation and FCC and safety agency compliance.

1.Unpack the HCS6600 unit(s) and all accessories. Accessories provided: IEEE-1394 Cable (Length = 1 meter)

2.Select the slot(s) in the card frame in which to install the HCS6600. Note: All cards must be used in an LG-approved card frame for this product.

3.Remove the AC power cord for the card frame from the power outlet.

4.Remove the blank cover plate from each slot into which a card is to be inserted.

5.Without using force, slide each new card into its designated slot, and ensure that it is fully inserted.

6.Engage and tighten the top and bottom thumbscrews securely. Note that the thumb- screws should only be finger tight; overtighten- ing may damage the assembly.

7.Refer to the diagram on page 10 for cable connections, and complete the system instal- lation and test procedure on page 11.

206-4119 9