Liebherr 131113 7085462 - 01 operating instructions Control

Control

5.4.1 Food refrigeration

Note

The energy consumption increases and the cooling perform- ance decreases if the ventilation is inadequate.

u Always keep the air slits of the fan free.

u Place butter and preserves in the upper area and in the door (see Appliance at a glance).

u Use recyclable plastic, metal, aluminium and glass containers and cling film for wrapping.

u Always store liquids and food which is subject to odour or taste transfer in closed containers or cover them.

u Foods which give off a large amount of ethylene gas and delicate foods, such as fruit, vegetables, salad, should always be stored separately or wrapped so as not to reduce the storage life; e.g. do not store tomatoes together with kiwis or cabbage.

u Use the front area of the refrigerator compartment floor only for briefly putting down cooled products, e.g. when rear- ranging and sorting. However do not leave cooled products there otherwise they may be pushed back or tipped over when the door is closed.

u Do not store food too close together to enable good air circulation.

5.4.2 Setting the temperature

The temperature depends on the following factors:

-the frequency of opening the door

-the room temperature of the installation location

-the type, temperature and quantity of the food

The temperature can be set from 9 °C to 3 °C, the recom- mended temperature is 5 °C.

Note

If the temperature is to be colder than 3 °C: u set the cooling temperature to 3 °C.

u Set the BioFresh temperature to a value between b4 (slightly colder) and b1 (coldest) (see 5.5)

u For a higher temperature setting: press Up button, refriger- ator compartment Fig. 2 (3).

u For a lower temperature setting: press Down button, refrig- erator compartment Fig. 2 (4).

w When the button is pressed for the first time, the previously set value is indicated, flashing, in the refrigerator compart- ment temperature display.

u To change the temperature in 1 °C steps: briefly press the button.

u To change the temperature continuously: hold down the button.

w The value is displayed flashing during the setting operation. w The actual temperature is displayed about 5 s after the last

press of a button. The temperature slowly adjusts to the new value.

5.4.3 SuperCool
With SuperCool you switch to the highest cooling
performance to reach lower cooling temperatures.
Use SuperCool, to rapidly cool large amounts of		*
food.
The SuperCool function uses slightly more energy.
Cooling with SuperCool
u Briefly press SuperCool button Fig. 2 (6).	display.
w The SuperCool symbol Fig. 2 (7) lights up in the

w The cooling temperature drops to the coldest value. Super- Cool is activated.

w SuperCool is automatically deactivated after 12 hours. The appliance continues to operate in the energy-saving, normal mode.

To prematurely deactivate SuperCool u Briefly press SuperCool button Fig. 2 (6).

w The SuperCool symbol Fig. 2 (7) goes out in the display. w SuperCool is deactivated.

5.4.4 Holiday mode

The holiday mode saves energy and prevents odour from occurring when the door of the refrigerator compartment stays closed for a lengthy period.

The freezer compartment remains in operation in the holiday mode.

Activating the holiday mode

u Remove all the food from the refrigerator and BioFresh compartment, otherwise they will perish..

u Press the holiday button Fig. 2 (5) for 3 sec.

wThe holiday mode is activated. The display indicates Ho.

Deactivating the holiday mode

uBriefly press the holiday button Fig. 2 (5). w The holiday mode is deactivated.

w The current cooling temperature is indicated in the display.

5.4.5 Shelves

Relocating the shelves

The shelves have stops preventing them from being uninten- tionally pulled out.

u Lift the shelf and draw it out forwards.

u Re-insert shelves at the required height. The stops must face downwards and lie behind the front shelves.

Dismantling shelves

u The shelves can be disman- tled for cleaning.

5.4.6 Using the sectioned shelf

u Slide the sectioned shelf under, as shown in the illus- tration.

Fig. 3

uThe glass plate (1) with pull-out stops must be at the front so that the stops (3) face downwards.

6 * Depending on model and options