Operation
- We recommend using a dedicated circuit for this appli- ance to prevent electrical overload.
- Follow all Federal, State and local electrical, fire and building codes and ordinances when installing the receptacle and / or the appliance.
- In some communities, a wall switch is required to turn power to the appliance ON and OFF.
- To reduce the risk of fire, electric shock, or personal injury, installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards, including
- The Power Plug must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance.
- The top of the electric outlet must be located within
4.5 Switching on the appliance
Switch on the appliance 2 hours before loading with frozen food for the first time.
Do not load frozen foods until the temperature display reads 0 °F
u Open the door.
u Press On/Off button Fig. 2 (8).
w The temperature display and the Alarm symbol will flash until the temperature is cold enough. If the temperature is greater than 32 °F (0 °C), flashing dashes will appear; if the temperature is lower than this, the current temperature will flash on the display.
w The interior light comes on when the door is opened. w Whenever “DEMO” appears on the display, the appli-
ance is running in demonstration mode. Contact the customer service department.
5 Operation
5.1 Temperature display unit
The temperature display can be changed from °F to °C.
5.1.1 To change the unit
u Activate setting mode: Press SuperFrost button Fig. 2 (9) for about 5 seconds.
w S is displayed in the temperature display. w The Menu symbol Fig. 2 (3) lights up.
u Using Up button Fig. 2 (1)/ Down button Fig. 2 (2) select °.
u To confirm: Briefly press SuperFrost button Fig. 2 (9).
u Using Up button Fig. 2 (1)/ Down button Fig. 2 (2) select °F or °C.
u To confirm: Briefly press SuperFrost button Fig. 2 (9).
u To exit setting mode: Press On/Off button Fig. 2 (8).
u Wait 5 minutes.
w The temperature is again displayed in the temperature display.
5.2Brightness of the temperature display
You can adapt the brightness of the temperature display to the light conditions in the room in which it is installed.
If the door is open or the control panel is used the temper- ature indicator lights up at maximum brightness. About 1 minute after the door is closed or no button has been pressed on the control panel, the temperature display goes back to the set brightness.
5.2.1 Setting the brightness
The brightness can be set between h0 (minimum lumi- nosity) and h5 (maximum luminosity).
u To activate setting mode: Press SuperFrost button Fig. 2 (9) for about 5 seconds.
w S is shown on the display.
w The Menu symbol Fig. 2 (3) lights up.
u Using Up button Fig. 2 (1) or Down button Fig. 2 (2) select h.
u To confirm: Briefly press SuperFrost button Fig. 2 (9).
u To set the display brighter: Press Up button Fig. 2 (1).
u To set the display darker: Press Down button Fig. 2 (2).
u To confirm: Press SuperFrost button Fig. 2 (9). w The brightness is set to the new value.
u To deactivate setting mode: Press On/Off button Fig. 2 (8).
u Wait 5 minutes.
w The temperature is again displayed in the temperature display.
5.3 Child-proof lock
You can use the
5.3.1 Switching on the child-proof lock
u Activate setting mode: press and hold the SuperFrost button Fig. 2 (9) for approximately 5 s.
w S is shown on the display.
w The Menu symbol Fig. 2 (3) lights up.
u Using the Up button Fig. 2 (1) or Down button Fig. 2 (2), select c.
u Press the SuperFrost button Fig. 2 (9) briefly to confirm. When c1 is shown on the display:
u To switch on the
|
|
|
* Depending on model and options | 7 | |
